DURABLE PORTFOLIO
Product Data Sheet
G41102 Satin TamperfasTM Vinyl/S730/94#SF
Spec#: 79450 - Restricted
FacestockFacestock physical properties
2 Mil TamperfasTM Vinyl is a matte (Satin) white cast vinyl film designed specifically for security labeling.  It is a frangible film so will break apart with any attempt to remove label after dispensing onto substrate.  Care should be taken in qualifying a particular die configuration to ensure proper strippability.   Standard shelf life is 6 months from date of purchase when stored at 70° F/50% R.H.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
50.80
Tensile:
ASTM D882
MD
psi
0
CD
15
psi
0
AdhesiveAdhesive physical properties
S730 is a clear solvent acrylic permanent adhesive for general purpose industrial applications. Features good intial tack and ultimate adhesion to a wide variety of substrates including medium to low surface energy plastics, and high shear for minimal cold flow or ooze characteristics.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Acrylic
Caliper:
ASTM D1000
0.0009
inches
22.86
micron
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
59.2
oz/inch
65.1
N/100 mm
LinerLiner physical properties
94# Stay-Flat is a bleached kraft paper stock. Offers excellent layflat characteristics for roll-to-sheet applications. Diecutting and stripping characteristics are good, but caution is suggested for intricate die configurations. Not recommended for fanfolding. Features fair back printability.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0070
inches
177.8000
microns
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
94.0
lbs/ream
150.4
g/sq m
Tensile:
ASTM D882
MD
40.0
lb/inch
176.0
N/25 mm
CD
20.0
in/inch
88.0
N/25 mm
Tear:
TAPPI T414
MD
2.6
ounces
73.8
grams
CD
3.0
ounces
85.2
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
45
N/A

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits Note: Although the adhesive is suitable for use up to 300°F, the facestock is limited to 225°F

Applications and Uses
Printing and Converting
Tamperfas™ Vinyl is printable with most standard flexographic and UV letterpress inks. For specific diecutting requirements, consult the Technical Marketing Bulletin for Tamperfas™. Due to manufacturing requirements, there might be a maximum of 15 splices per 1,668 yards. Standard shelf life is amended to 6 months from date of purchase when stored at 70° F/50% R.H. It is strongly recommended that the product be converted and applied to substrate within 6 months of purchase. Due to inherent properties of this unique product, facestock shrinkage does occur. Exposure to environmental conditions other than those recommended will accelerate facestock shrinkage or liner growth. Either condition can make the product unusable. Not recommended for automatic application.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511