DURABLE PORTFOLIO
Product Data Sheet
2 Mil Clear Print-Treated Polyester/S8020/40#BG
Spec#: 77845 Durable
FacestockFacestock physical properties
2 Mil Clear Print-Treated Polyester is a highly transparent overlaminating film facestock featuring excellent tear strength, heat resistance, dimensional stability and chemical resistance. Print treatment is designed to enhance printability with a variety of printing processes.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
33,500
psi
2,355
kg/sq cm
CD
33,500
psi
2,355
kg/sq cm
AdhesiveAdhesive physical properties
S8020 is a clear, permanent acrylic adhesive designed for overlaminating films. It exhibits a balance of high cohesive strength and adhesion to low surface-energy substrates. Specifically designed to exhibit excellent wetout characteristics, good yellowing resistance, and excellent clarity.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0007
inches
17.78
micron
Standard Coat Wt:
19
g/sq m
Minimum Appl Temp:
23
F
-5
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
40.0
oz/inch
44.0
N/100 mm
LinerLiner physical properties
40#BG is a bleached white glassine liner with excellent smoothness, density, and roll label converting properties.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0023
inches
58.4200
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
39.3
lbs
62.9
g/sq m
Tensile:
ASTM D882
MD
43.4
lbs/inch
191.0
N/25 mm
CD
17.0
lbs/inch
74.8
N/25 mm
Tear:
TAPPI T414
MD
1.2
ounces
34.0
grams
CD
1.5
ounces
42.5
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
40
0.0050 inches (5 mils; 127 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
Designed for overlamination of polyester or vinyl label materials to protect press printing from abrasion or chemical exposures.
Not recommend for bright metallic backgrounds or large dark flood coated surfaces. Use polyester linered overlaminations for bright or dark backgrounds.

Printing and Converting
Overlaminations can be aids in diecutting, matrix stripping, and automatic label dispensing.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. Stainless Steel

3. ABS Plastic

4. Polypropylene

5. HDPE

6. LDPE
77.1

67.7

58.9

24

11.7

11
84.8

74.5

64.8

26.4

12.9

12.1
70.2

84.8

77.8

0

4.4

13.2
77.2

93.3

85.6

0

4.8

14.5
86.2

90

73.3

11

11

8.8
94.8

99

80.6

12.1

12.1

9.7
112.6

124.3

54.6

1

20.5

1.4
123.9

136.7

60.1

1.1

22.6

1.5

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
81.5

72.5

76.8

36.7

29.6

38.7

33.7

79.4

50.72

69

60.7
89.7

79.8

84.5

40.4

32.6

42.6

37.1

87.3

55.8

75.9

66.8
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

3.1

6.4

0

3.3

3.1

0



Compliance Recognition: UL, C-U
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. on PET Labels

    2. on PVC Labels
-40

-40
-40

-40
302

140
150

60
I/O

I/O
Recognized Ribbons:



Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. on PET Labels

    2. on PVC Labels
-40

-40
-40

-40
302

140
150

60
I/O

I/O
Recognized Ribbons:


409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511