DURABLE PORTFOLIO



Product Data Sheet
Fasson® 2 Mil Bright Chrome Polyester TC/S8001/50#SCK
Spec#: 78388

FacestockFacestock physical properties
2 Mil Bright Chrome Polyester TC is a bright metallic film featuring excellent tear strength, heat resistance, dimensional stability, opacity and chemical resistance. Designed for printing with most solvent and some water-based flexographic inks. Suitable for thermal transfer printing applications with select thermal transfer ribbons. Specific testing required.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
31,200
PSI
2,193
kg/sq cm
CD
36,900
PSI
2,594
kg/sq cm

AdhesiveAdhesive physical properties
S8001 is a high performance, clear permanent emulsion acrylic pressure sensitive adhesive with balanced adhesion to a wide variety of substrates, including low surface energy plastics, engineering grade plastics, bare, coated, or painted metals, including powder coat and enamel paints. It features medium tack and excellent chemical and UV resistance for outdoor industrial applications.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0010
inches
25.40
microns
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
302
F
150
C
Loop Tack Stainless
Steel: PSTC11
32.0
oz/inch
35.2
N/100 mm

LinerLiner physical properties
50# SCK is a bleached, super calendered paper stock with very good die-cutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs/ream
87.2
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
51.1
grams
CD
2.1
ounces
59.6
grams

Liner Release:
TMLI 90o removal of Liner from Facestock.
Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
30
0.006 inches (6 mils; 152 microns)

DURABLE PORTFOLIO



Product Data Sheet


Features and Benefits
Applications and Uses
Suitable for a variety of durable labeling applications such as:
Printing and Converting
The top coat is designed for printing by most solvent, UV cured, and water-based flexographic inks, UV cured letterpress and rotary screen inks. Specially formulated inks are not normally necessary, however, testing is recommended prior to final ink system selections. The following press inks have shown excellent results. Water-based flexogrphic inks: Environmental Inks & Coatings' "DR III FR"; Flint Ink's "HydroFilm ACRE"; and Water Ink Technologies' "Versifilm Plus ULF". UV Flexographic inks: Environmental Inks & Coatings' "UltraFlex III SFR"; Flint Ink's "Flexocure Sigma"; and Water Ink Technologies' "PharmaFlex UV". UL recognized with Environmental Inks and Coatings' "Aqua Plus" and "Aqua Film III" in blue and black colors, and Water Ink Technologies' "Water Gloss" ink in all colors. Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or the Fasson Thermal Transfer Ribbon Guide for specific recommendations. This product can be die cut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO



Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes. Data was generated from 2 mil polyester facestock applied clean labatory panels. See Tech Bulletin "Achieving Maximum Adhesion" for specifics.

Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. ABS Plastic

3. Polypropylene

4. HDPE

5. LDPE

6. Stainless Steel
33.8

42.3

11.0

25.5

8

35.2
37.2

46.5

12.1

28.1

8.8

38.7
58

68.9

38.4

32

56

60.4
63.9

75.8

42.1

35.2

61.6

66.5
66.9

54.7

33.9

31.1

6.8

42.9
73.6

60.1

37.3

34.2

7.5

47.2
98.4

71.8

27.7

36.2

16.5

50.6
108.3

79.0

30.5

39.8

18.2

55.7

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.

Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. K1 Kerosene

11. Heptane
46.2

40.1

51.2

19

44.8

49.2

21.7

46.4

39.4

45.7

39.6
50.8

44.1

56.4

20.9

49.3

54.1

23.9

51

43.3

50.2

43.5
No change

No change

No change

No change

No change

No change

No change

No change

No change

No change

No change
0

0

0

0

0

0

0

0

0

0

0

Compliance Recognition: UL, C-U
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)

Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RF", Astro Med "RY", Coding Prds "5940", DNP "R-300", DNP "R-510", DNP "Signature Series Resin", Iimak "SP-410", Iimak "SP-330", Iimak "Primemark", Intermec "TMX 1500", Intermec "TMX 3200", ITW "B324", Kurz "K300", Kurz "K500", Kurz "K501", NCR "Promark 3", NCR "Pacesetter", NCR "Ultra V", NCR "Perma Max", NCR "K3", Ricoh "B110C", Ricoh "B110CX", Ricoh "B110CR", Ricoh "120EC", Sato Corp. "Premier 1", UCA "US300", Zebra "5095", Zebra "5100", Zebra "5175", Zebra "5463", Zebra "Z-4100", and others.



Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Electrostatic Paints

    2. Metals

    3. Plastics Group I

    4. Plastics Group II

    5. Plastics Group III

    6. Plastics Group IV

    7. Plastics Group V

    8. Plastics Group VI

    9. Plastics Group VII

    10. Plastics Group VIII
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40
302

302

212

176

176

176

176

176

176

176
150

150

100

80

80

80

80

80

80

80
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", DNP "R-300", DNP "R-510", DNP "TR4070", DNP "Signature Series Resin", Kurz "K500", NCR "Promark 3", Ricoh "B110C", Ricoh "B110CR", Sato Corp. "Premier 1", UCA "US300", Zebra "5100", and others.


409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.


www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511