DURABLE PORTFOLIO
Product Data Sheet
Fasson® 4.2 Mil Smudgeproof Kimdura®/S4600/50#SCK
Spec#: 76953
FacestockFacestock physical properties
4.2 mil Smudgeproof Kimdura® is white biaxially oriented three-ply polypropylene film specially treated for computer imprintability. Suitable for thermal transfer printing applications with select ribbons.

Kimdura® is a registered trademark of Kimberly-Clark.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0042
inches
106.68
microns
Tensile:
ASTM D882
MD
6,000
PSI
422
kg/sq.cm
CD
17,000
PSI
1,195
kg/sq.cm.
AdhesiveAdhesive physical properties
S4600 is a clear general purpose emulsion permanent adhesive featuring good initial tack and ultimate adhesion to a wide variety of substrates.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0008
inches
20.32
microns
Standard Coat Wt:
23
g/sq m
Minimum Appl Temp:
10
F
-12
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
44.0
oz/inch
48.4
N/100 mm
LinerLiner physical properties
50# SCK is a bleached, super calendered paper stock with very good die-cutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs/ream
87.2
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
51.1
grams
CD
2.1
ounces
59.6
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
40
0.0081 inches (8.1 mils: 205.77 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
Printing and Converting
This product offers a specially treated, smudge-resistant surface which is impact printable. This material is also flexographic, letterpress printable, and receptive to a variety of thermal transfer ribbons. It is not recommended for web offset printing with conventional dryers where surface temperature of the facestock could exceed 180° F in the drying unit. Caution should be exercised when applying inks out to the edge of the label, particularly UV screen inks and UV cured varnishes. High shrinkage coatings can cause labels to lift off the liner or substrate. In-house testing is always recommended prior to ink/ribbon selection. This product can be diecut and stripped at high speeds on standard web-fed presses. Actual speeds will depend on ink coverage and die configuration. Because the fillers are highly abrasive, die life will be shortened. It is recommended that your die manufacturer be contacted for further suggestions. Sample labels in a variety of shapes have been dispensed and applied successfully with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.

Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. Stainless Steel

3. Polypropylene

4. HDPE

5. LDPE

6. ABS Plastic
59.7

58.9

54.7

45.3

29.1

57.8
65.7

64.8

60.2

49.8

32

63.6
61.6

57.1

57.8

42.1

35

62.3
67.8

62.8

63.6

46.3

38.5

68.5
59

55

55

49.4

27.5

53.9
64.9

60.5

60.5

54.3

30.3

59.3
113

106.4

110

92.6

38.7

94
124.3

117

121

101.9

42.6

103.4
Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.

Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
55.7

60

60

57.4

60

63.4

31

51.4

34.1

64.6

47.8
61.3

66

66

63.1

66

69.7

34.1

56.5

37.5

71.1

52.6
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

0

3.81

0

2.54

0.25

4.3

Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511