DURABLE PORTFOLIO
Product Data Sheet
Fasson® 2 Mil TamperfasTM Satin Vinyl/S730/50#SCK ABC
(Standard shelf life is amended to 6 months from date of purchase when stored at 70° F/50% R.H.)
Spec#: 79449
FacestockFacestock physical properties
2 Mil TamperfasTM Vinyl is a satin white cast vinyl film designed specifically for security labeling. Care should be taken in qualifying a particular die configuration to ensure proper strippability. Standard shelf life is amended to 6 months from date of purchase when stored at 70° F/50% R.H.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
50.80
micron
Tensile:
ASTM D882
MD
5
psi
0
CD
5
psi
0
AdhesiveAdhesive physical properties
S730 is a clear solvent acrylic permanent adhesive for general purpose industrial applications. Features good intial tack and ultimate adhesion to a wide variety of substrates including medium to low surface energy plastics, and high shear for minimal cold flow or ooze characteristics.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Acrylic
Caliper:
ASTM D1000
0.0009
inches
22.86
micron
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
59.2
oz/inch
65.1
N/100 mm
LinerLiner physical properties
50#SCK is a bleached, super calendered kraft paper liner with very good diecutting and matrix stripping properties. Supplied with an anti-block coating on the backside of the liner to control adhesive and label transfer to the backside of the liner in finished, wound rolls. This liner should not be used in fanfolded label applications, and is not recommended for back printability.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.0
lbs/ream
86.4
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.7
ounces
48.3
grams
CD
2.0
ounces
56.8
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
20
0.0063 inches (6.3 mils; 160 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits Note: Although the adhesive is suitable for use up to 300°F, the facestock is limited to 225°F

Applications and Uses
Printing and Converting
Tamperfas™ Vinyl is printable with most standard flexographic and UV letterpress inks. For specific diecutting requirements, consult the Technical Marketing Bulletin for Tamperfas™. Due to manufacturing requirements, there might be a maximum of 15 splices per 1,668 yards. Standard shelf life is amended to 6 months from date of purchase when stored at 70° F/50% R.H. It is strongly recommended that the product be converted and applied to substrate within 6 months of purchase. Due to inherent properties of this unique product, facestock shrinkage does occur. Exposure to environmental conditions other than those recommended will accelerate facestock shrinkage or liner growth. Either condition can make the product unusable. Not recommended for automatic application.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes. This data was obtained with the adhesive applied to 2 mil polyester facestock. It is not possible to conduct these tests with Tamperfas™facestock due to the fragile nature of the facestock.

Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. Stainless Steel

3. ABS Plastic

4. Polypropylene

5. HDPE

6. LDPE
77.1

67.7

58.9

24

11.7

11
84.8

74.5

64.8

26.4

12.9

12.1
70.2

84.8

77.8

0

4.4

13.2
77.2

93.3

85.6

0

4.8

14.5
86.2

90

73.3

11

11

8.8
94.8

99

80.6

12.1

12.1

9.7
112.6

124.3

54.6

1

20.5

1.4
123.9

136.7

60.1

1.1

22.6

1.5

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
81.5

72.5

76.8

36.7

29.6

38.7

33.7

79.4

50.72

69

60.7
89.7

79.8

84.5

40.4

32.6

42.6

37.1

87.3

55.8

75.9

66.8
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

3.1

6.4

0

3.3

3.1

0



Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511