DURABLE PORTFOLIO



Product Data Sheet
2 Mil Clear Printable Polyester/S730/50#SCK ABC
Spec#: 61319

FacestockFacestock physical properties
2 Mil Clear Print-Treated Polyester is a highly transparent film facestock featuring excellent tear strength, heat resistance, dimensional stability and chemical resistance. Print treatment is designed to enhance printability with a variety of printing processes.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
33,500
psi
2,355
kg/sq m
CD
33,500
psi
2,355
kg/sq m

AdhesiveAdhesive physical properties
S730 is a clear solvent acrylic permanent adhesive for general purpose industrial applications. Features good intial tack and ultimate adhesion to a wide variety of substrates including medium to low surface energy plastics, and high shear for minimal cold flow or ooze characteristics.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Acrylic
Caliper:
ASTM D1000
0.0009
inches
22.86
micron
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
59.2
oz/inch
65.1
N/100 mm

LinerLiner physical properties
50#SCK is a bleached, super-calendered paper stock with very good diecutting and matrix stripping properties. Supplied with an Anti Block Coating ("ABC") on the backside of the liner to control adhesive and label transfer to the backside of the liner in finished, wound rolls. This liner should not be used in fanfolded label applications and is not recommended for back printability.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs/ream
88.8
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
49.9
grams
CD
2.1
ounces
58.2
grams

Liner Release:
TMLI 90o removal of Liner from Facestock.
Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
55
0.0061 inches

DURABLE PORTFOLIO



Product Data Sheet


Features and Benefits
Applications and Uses
This product is suitable for wide variety of durable labeling applications such as:
Printing and Converting
The surface treatment is designed for printing by flexography with most solvent and some water based inks. Specially formulated inks are normally not needed, however, testing is recommend prior to final ink selection. This product can be die cut and stripped at high speeds on standard web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO



Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.

Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. Stainless Steel

3. ABS Plastic

4. Polypropylene

5. HDPE

6. LDPE
77.1

67.7

58.9

24

11.7

11
84.8

74.5

64.8

26.4

12.9

12.1
70.2

84.8

77.8

0

4.4

13.2
77.2

93.3

85.6

0

4.8

14.5
86.2

90

73.3

11

11

8.8
94.8

99

80.6

12.1

12.1

9.7
112.6

124.3

54.6

1

20.5

1.4
123.9

136.7

60.1

1.1

22.6

1.5

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
81.5

72.5

76.8

36.7

29.6

38.7

33.7

79.4

50.72

69

60.7
89.7

79.8

84.5

40.4

32.6

42.6

37.1

87.3

55.8

75.9

66.8
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

3.1

6.4

0

3.3

3.1

0



Compliance Recognition: UL, CSA, C-U
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Aluminum

    2. Acrylic Paint

    3. Epoxy Paint

    4. Galvanized Steel

    5. Stainless Steel

    6. Alkyd Enamel

    7. Polyester Paint

    8. Nylon

    9. Phenolic

    10. ABS Plastic

    11. Polyphenylene Oxide

    12. Polycarbonate

    13. Unsat Thermoset Polyester

    14. Chrome plate

    15. Polystyrene

    16. Tedlar

    17. and others
-40

-40

-40

-40

-40

-40

-40

-40

-20

-40

-20

-20

-20

-20

-20

-20


-40

-40

-40

-40

-40

-40

-40

-40

-29

-40

-29

-29

-29

-29

-29

-29


302

257

257

212

212

212

212

212

212

176

176

176

176

140

140

212


150

125

125

100

100

100

100

100

100

80

80

80

80

60

60

100


I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I

I

I



Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RY", Coding Prds "5940", DNP "R-300", DNP "TR4070", DNP "Signature Series Resin", Iimak "SP-410", Iimak "SP-330", Iimak "Primemark", ITW "B324", Kurz "K500", Ricoh "B110C", Ricoh "B110CR", Sato Corp. "Premier 1", Sony "TR5070", Sony "TR6070", Sony "TR6075", UCA "US300", Zebra "5095", Zebra "5100", Zebra "5175", Zebra "5555", Zebra "Z-4100", and others.

Canadian Standards Association
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only
I/O=Indoor & Outdoor)
    1. Metals

    2. Plastics Group I

    3. Plastics Group II

    4. Plastics Group III

    5. Plastics Group V

    6. Plastics Group VI

    7. Plastics Group VII

    8. Plastics Group VIII
-40

-40

-40

-40

-40

-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40
302

212

176

176

176

176

176

176
150

100

80

80

80

80

80

80
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Acceptable Ribbons: Iimak "SP-330", Sato Corp. "Premier 1", Sony "TR5070", Zebra "5095"


Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Metals

    2. Plastics Group I

    3. Plastics Group II

    4. Plastics Group III

    5. Plastics Group V

    6. Plastics Group VI

    7. Plastics Group VII

    8. Plastics Group VIII
-40

-40

-40

-40

-40

-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40
302

212

176

176

176

176

176

176
150

100

80

80

80

80

80

80
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med "RY", DNP "TR4070", Iimak "SP-330", Kurz "K500", NCR "Promark 3", Ricoh "B110C", Sato Corp. "Premier 1", Sony "TR4075", Sony "TR5070", Sony "TR6075", Zebra "Z-4100", and others.


409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.


www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511