DURABLE PORTFOLIO



Product Data Sheet
2 Mil White Polyester TC/S333/50#SCK ABC
Spec#: 72825 DURABLE

FacestockFacestock physical properties
2 Mil White Polyester TC is a homogeneously pigmented white facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
21,300
PSI
1,497
kg/cm2
CD
28,400
PSI
1,997
kg/cm2

AdhesiveAdhesive physical properties
S-333 An excellent general purpose industrial grade clear permanent acrylic adhesive. Features high initial tack to most high and medium surface energy substrates. High shear strength for low ooze characteristics.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0008
inches
20.32
micron
Standard Coat Wt:
26
g/sq m
Minimum Appl Temp:
25
F
-4
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
35.8
oz/inch
39.4
N/100 mm

LinerLiner physical properties
50#SCK is a bleached, super-calendered paper stock with very good diecutting and matrix stripping properties. Supplied with an Anti Block Coating ("ABC") on the backside of the liner to control adhesive and label transfer to the backside of the liner in finished, wound rolls. This liner should not be used in fanfolded label applications and is not recommended for back printability.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs/ream
88.8
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
49.9
grams
CD
2.1
ounces
58.2
grams

Liner Release:
TMLI 90o removal of Liner from Facestock.
Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
40
0.006 inches (6 mils; 152 micron)

DURABLE PORTFOLIO



Product Data Sheet


Features and Benefits
Applications and Uses
This product is suitable for a variety of durable labeling applications such as:
Printing and Converting
The topcoat is designed for printing by most solvent, UV cured, and water-based flexographic inks, UV cured letterpress, and rotary screen inks. Specially formulated inks are normally not necessary; however, testing is recommended prior to final ink selection. Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or Fasson Thermal Transfer Ribbon Guide for specific recommendations. This product can be diecut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO



Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.

Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. Stainless Steel

3. ABS Plastic

4. Polypropylene

5. HDPE

6. LDPE
55

36.5

51.5

19

11.2

13
61

40.2

56.7

21

12.3

14.3
60

59.6

62.9

5.4

12.9

28
66

65.6

69.2

5.9

14.2

31
63

68.4

60.2

28

17.2

12
70

75.2

66.2

31

18.9

13
89

70.4

37.1

19

33.4

15
98

77.4

40.8

21

36.7

16

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.

Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Toluene

6. Brake Fluid

7. Reference Fuel C

8. Kerosene K1

9. Heptane
57.3

40.5

46

26.5

12.4

48.96

21.12

41.3

47.5
63

44.6

50.6

29.2

13.6

53.9

23.2

45.4

52.3
No Chnage

No Change

No Change

No Change

No Change

No Change

No Change

No Chnage

No Change
3.8

0

0

0

3.3

0

10.2

0

0

Compliance Recognition: UL, CSA
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Aluminum

    2. Galvanized Steel

    3. Stainless Steel

    4. Acrylic Paint

    5. Epoxy Paint

    6. Porcelain

    7. Alkyd Enamel

    8. Polyester Paint

    9. Nylon

    10. Polycarbonate

    11. Melamine

    12. Polystyrene

    13. ABS Plastic

    14. Unsat Thermoset Polyester

    15. Phenolic

    16. Polyphenylene Oxide

    17. Polyethylene

    18. and others
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40




-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40




302

302

302

302

302

302

302

302

212

212

212

176

176

212

212

176

140


150

150

150

150

150

150

150

150

100

100

100

80

80

100

100

80

60


I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I

I

I

I



Recognized Ribbons: Armor "AXR7+", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RF", Iimak "SP-410", Iimak "SP-330", Iimak "Primemark", Intermec "TMX 1500", Intermec "TMX 3200", ITW "B324", Kurz "K300", Kurz "K500", Kurz "K501", NCR "Promark 3", NCR "Perma Max", NCR "K3", Ricoh "B110C", Ricoh "B110CX", Ricoh "120EC", Sato Corp. "Premier 1", Zebra "5095", Zebra "5100", Zebra "5463", Zebra "Z-4100", and others., Fujicopian FTX303, Fujicopian FTX303N, Fujicopian TTM-164, Fujicopian FTX304, Fujicopian TTM-46, Fujicopian FTX100, Fujicopian TRX-21, Dai Nippon "R-300", Dai Nippon "R-510", ITW "R-91, Japan Pulp & Paper "Resin 1", Japan Pulp & Paper "Sigma P", NCR "Resin Max", Sony "TR4070", Sony "TR4075", Sony "TR5070", Sony "TR6070", Sony "TR6075", Sony "Signature Series Resin", Union Chemicar "US300"

Canadian Standards Association
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only
I/O=Indoor & Outdoor)
    1. Metals

    2. Plastics Group I

    3. Plastics Group II

    4. Plastics Group III

    5. Plastics Group V

    6. Plastics Group VI

    7. Plastics Group VII

    8. Plastics Group VIII
-40

-40

-40

-40

-40

-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40
302

212

176

176

176

176

176

176
150

100

80

80

80

80

80

80
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Acceptable Ribbons: Iimak "SP-330", NCR "Promark 3", Ricoh "B110C", Sato Corp. "Premier 1", Zebra "5095", Zebra "Z-4100", Fujicopian FTX303, Fujicopian FTX303N, Fujicopian TTM-164, Dai Nippon "R-300", Dai Nippon "R-510", ITW "R-91, Japan Pulp & Paper "Resin 1", Sony "TR4070", Sony "TR5070", Sony "Signature Series Resin"




409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.


www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511