DURABLE PORTFOLIO
Product Data Sheet
Fasson® 2 Mil White Polyester TC/S8001/50#SCK
Spec#: 78385 Durable
FacestockFacestock physical properties
2 Mil White Polyester TC is a homogeneously pigmented white facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
21,300
PSI
1,497
kg/cm2
CD
28,400
PSI
1,997
kg/cm2
AdhesiveAdhesive physical properties
S8001 is a high performance, clear permanent emulsion acrylic pressure sensitive adhesive with balanced adhesion to a wide variety of substrates, including low surface energy plastics, engineering grade plastics, bare, coated, or painted metals, including powder coat and enamel paints. It features medium tack and excellent chemical and UV resistance for outdoor industrial applications.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0010
inches
25.40
microns
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
302
F
150
C
Loop Tack Stainless
Steel: PSTC11
32.0
oz/inch
35.2
N/100 mm
LinerLiner physical properties
50#SCK is a bleached super-calendered kraft stock featuring high internal strength, toughness, and tear resistance. Ideally suited for marginal punching, perforating, and fanfolding.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
57.7
lbs/ream
92.3
g/sq m
Tensile:
ASTM D882
MD
51.0
psi
229.5
N/25mm
CD
22.7
psi
102.1
N/25mm
Tear:
TAPPI T414
MD
2.0
ounce
57.0
grams
CD
2.7
ounce
77.0
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
30
0.006 inches (6 mils; 152 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
Suitable for a variety of durable labeling applications such as:
Printing and Converting
The top coat is designed for printing by most solvent, UV cured, and water-based flexographic inks; UV cured letterpress, Digital and rotary screen inks. Specially formulated inks are not normally necessary, however, testing is recommended prior to final ink system selections.
Note: With most press inks, overlamination is required to meet the abrasion requirement for c-UL (CSA) recognition. At the 150ºC recognition temperature, overlaminations darken enough to hinder the readability of most yellow colored inks. If overlamination is desired with UL969,c-UL or CSA recognition, seek recognition at a lower maximum use temperature.

Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or the Fasson Thermal Transfer Ribbon Guide for specific recommendations. This product can be die cut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes. Data was generated from samples with 2 mil polyester facestocks, applied to clean labatory panels. See Tech Bulletin "Achieving Maximum Adhesion" for specifics.

Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. ABS Plastic

3. Polypropylene

4. HDPE

5. LDPE

6. Stainless Steel
33.8

42.3

11.0

25.5

8

35.2
37.2

46.5

12.1

28.1

8.8

38.7
58

68.9

38.4

32

56

60.4
63.9

75.8

42.1

35.2

61.6

66.5
66.9

54.7

33.9

31.1

6.8

42.9
73.6

60.1

37.3

34.2

7.5

47.2
98.4

71.8

27.7

36.2

16.5

50.6
108.3

79.0

30.5

39.8

18.2

55.7

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.

Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. K1 Kerosene

11. Heptane
46.2

40.1

51.2

19

44.8

49.2

21.7

46.4

39.4

45.7

39.6
50.8

44.1

56.4

20.9

49.3

54.1

23.9

51

43.3

50.2

43.5
No change

No change

No change

No change

No change

No change

No change

No change

No change

No change

No change
0

0

0

0

0

0

0

0

0

0

0

Compliance Recognition: UL, C-U
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Acrylic Paint

    2. Acrylic PCP*

    3. Alkyd Enamel

    4. Aluminum

    5. Anodized Aluminum

    6. Epoxy Paint

    7. Epoxy PCP*

    8. Galvanized Steel

    9. Polyester Paint

    10. Polyester PCP*

    11. Polyurethane PCP*

    12. Porcelain

    13. Stainless Steel

    14. Melamine

    15. Phenolic

    16. Polycarbonate

    17. Thermoset Polyester

    18. ABS Plastic

    19. PBT Plastic

    20. Polypropylene

    21. Polyethylene

    22. Polyphenylene Oxide

    23. Polystyrene
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40



-40

-40
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40



-40

-40
302

302

302

302

302

302

302

302

302

302

302

302

302

212

212

212

212

176

176

176

176

176

176
150

150

150

150

150

150

150

150

150

150

150

150

150

100

100

100

100

80

80

80

80

80

80
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I

I/O

I/O
Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RF", Astro Med "RY", Coding Prds "5940", DNP "R-300", DNP "R-510", DNP "TR4070", DNP "Signature Series Resin", Iimak "SP-410", Iimak "SP-330", Iimak "Primemark", Intermec "TMX 1500", Intermec "TMX 3200", ITW "B324", Kurz "K300", Kurz "K500", Kurz "K501", NCR "Promark 3", NCR "Pacesetter", NCR "Ultra V", NCR "Perma Max", NCR "K3", Ricoh "B110C", Ricoh "B110CX", Ricoh "B110CR", Ricoh "120EC", Sato Corp. "Premier 1", UCA "US300", Zebra "5095", Zebra "5100", Zebra "5175", Zebra "5463", Zebra "Z-4100", and others.



Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Electrostatic Paints

    2. Metals

    3. Plastics Group I

    4. Plastics Group II

    5. Plastics Group III

    6. Plastics Group IV

    7. Plastics Group V

    8. Plastics Group VI

    9. Plastics Group VII

    10. Plastics Group VIII

    11. Glass
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40
302

302

212

176

176

176

176

176

176

176

257
150

150

100

80

80

80

80

80

80

80

125
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O
Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", DNP "R-300", DNP "R-510", DNP "TR4070", DNP "Signature Series Resin", Kurz "K500", NCR "Promark 3", Ricoh "B110C", Ricoh "B110CR", Sato Corp. "Premier 1", UCA "US300", Zebra "5100", and others.


409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511