Fasson® PRIMAX® 250 is a corona-treated, flexible, opaque white polyolefin film with exceptional dimensional stability for use in a wide range of applications, including prime label. Printable by web screen, UV letterpress, flexo solvent, and water-based inks. In-line corona treatment will greatly expand the number of inks which can be used. Use caution when applying inks out to the edge of the label, particularly UV screen inks and UV cured varnishes. High shrinkage coatings can cause labels to lift off the liner or substrate. In-house testing is always recommended prior to final ink selection. This product can be diecut and stripped at high speeds on standard web-fed presses using typical film tooling. Excellent dispensability with direct comparison to white Opticite* and better performance over clear MDPE and clear flex vinyl.

Opticite* is a trademark of The Dow Chemical Company.

	Basis Weight:	N/A
	Caliper:	0.0025 inches ± 10%
	Tensile:	MD 17,200 psi CD 2,300 psi
	Tear:	N/A
	Stiffness:	MD 20 mg

Adhesive:
Fasson® S1000 is a clear permanent adhesive specifically designed to exhibit excellent wet-out characteristics on clear films. Frequently used in the prime label market where squeezability and clear labeling are critical. Meets the requirements of FDA Compliance: Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105). Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.

	Type:	Emulsion acrylic
	Minimum Application Temperature:	+10° F
	Service Temperature Range:	-40° F to +200° F, subject to facestock limitations

Typical Performance Data: , 2 Mil Clear Polyester facestock at room temperature on standard lab panels

	Stainless Steel Loop Tack: Peel Adhesion:	3.2 - 3.6 lbs 1.9 - 2.3 lbs
	HDPE Loop Tack: Peel Adhesion:	1.0 - 1.5 lbs 0.8 - 1.3 lbs
	Glass Loop Tack: Peel Adhesion:	2.8 - 3.3 lbs 2.0 - 2.3 lbs

Liner:
A 1.5 mil durable polyester liner suitable for high-speed diecutting and stripping applications. Used primarily for roll-to-roll, high-speed dispensing applications.

	Basis Weight:	N/A
	Caliper:	0.0015 inches ± 10%
	Tensile:	MD 32,000 psi
	Tear:	N/A

Adhesive:
Fasson® S1000 is a clear permanent adhesive specifically designed to exhibit excellent wet-out characteristics on clear films. Frequently used in the prime label market where squeezability and clear labeling are critical. Meets the requirements of FDA Compliance: Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105). Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.

	Type:	Emulsion acrylic
	Minimum Application Temperature:	+10° F
	Service Temperature Range:	-40° F to +200° F, subject to facestock limitations

Typical Performance Data: , 2 Mil Clear Polyester facestock at room temperature on standard lab panels

	Stainless Steel Loop Tack: Peel Adhesion:	3.2 - 3.6 lbs 1.9 - 2.3 lbs
	HDPE Loop Tack: Peel Adhesion:	1.0 - 1.5 lbs 0.8 - 1.3 lbs
	Glass Loop Tack: Peel Adhesion:	2.8 - 3.3 lbs 2.0 - 2.3 lbs

Liner:
40#SCK is a bleached super-calendered kraft stock featuring high internal strength, toughness, and tear resistance. Used primarily for roll-to-roll label applications.

	Basis Weight:	42.40# per ream, ± 10% (500 sheets 24" x 36")
	Caliper:	0.00244 inches ± 10%
	Tensile:	MD 39.70# per inch width CD 14.70# per inch width
	Tear:	MD 34.70 grams CD 41.80 grams

Total Construction Caliper (approximate): 0.00804 inches ±10%



Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Statement of Practical Use
All materials, sales and contracts for sale of Avery Dennison products are sold with the express requirement and understanding that the customer is solely and exclusively responsible for testing and for ensuring the products are fit for the customer's purposes or an end-user's purposes. All express or implied warranties of merchantability and fitness for particular use are disclaimed.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

label.averydennison.com

Label and Packaging Materials-North America 8080 Norton Parkway Mentor, OH 44060 800-944-8511