DURABLE PORTFOLIO



Product Data Sheet
Fasson® 2 Mil White Print-Treated Polyester/R143/50#SCK
Spec#: 71055

FacestockFacestock physical properties
2 Mil White Print-Treated polyester is a pigmented white semi-glossy film facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance. The print treatment is designed to enhance printability with a variety of printing processes.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
21,000
psi
1,476
kg/sq cm
CD
31,000
psi
2,179
kg/sq cm

AdhesiveAdhesive physical properties
R143 is a visually clear acrylic based removable adhesive with versatile performance properties. It features superior cohesive strength for high creep resistance, moderately high tack and adhesion, yet clean repositionability over extended contact periods on most substrates. This adhesive complies with the European Directive 2002/95/EC of January 27, 2003, for the restriction of use of certain hazardous substances.
Imperial Value
Units
Metric Value
Units
Type:
Solvent acrylic
Caliper:
ASTM D1000
0.0009
inches
22.86
microns
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
250
F
121
C
Loop Tack Stainless
Steel: PSTC11
20.0
oz/inch
22.0
N/100 mm

LinerLiner physical properties
50# SCK is a bleached, super calendered paper stock with very good die-cutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs/ream
87.2
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
51.1
grams
CD
2.1
ounces
59.6
grams

Liner Release:
TMLI 90o removal of Liner from Facestock.
Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
60
0.0061 incheds (6.1 mils; 154.9 microns)

DURABLE PORTFOLIO



Product Data Sheet


Features and Benefits
Applications and Uses
This product is suitable for a variety of durable labeling applications such as:
Printing and Converting
The surface treatment is designed for printing by most solvent, UV cured, and water-based flexographic inks, UV cured letterpress, and rotary screen inks. Specially formulated inks are normally not necessary; however, testing is recommended prior to final ink selection. Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or Fasson Thermal Transfer Ribbon Guide for specific recommendations. This product can be diecut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO



Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.
Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Stainless Steel

2. Aluminum

3. Polypropylene

4. HDPE

5. LDPE

6. ABS Plastic
14.4

14.4

4.8

3.2

0

9.6
15.8

15.8

5.3

3.5

0

10.6
18.9

17.6

5.76

4.47

0

13.9
20.8

19.4

6.3

4.9

0

15.3
18.1

8.8

9.44

4.32

0

13
19.9

9.7

10.4

4.8

0

14.3
32.48

13.76

8.48

7.52

1.44

12.8
35.7

15.1

9.3

8.3

1.6

14.1
Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.
Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
9.1

3.84

17

6.6

3.68

3.8

5.9

14.4

9.1

8.5

10.9
10

4.2

18.7

7.3

4

4.2

6.5

15.8

10

9.4

12
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

Edge Lift

No Change

No Change
0

0

0

0

0

0

0

0

Lifted

0

0



Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.


www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511