Print this Page
Fasson® 60# Classic® Laid Solar White WS FSC®/S100R/44#PK
Spec# 12649
Facestock:
Fasson® 60# Classic® Laid Solar White WS FSC® is a sixty pound uncoated paper featuring a laid finish with a wet strength additive to increase resistance to tearing and shriveling in moist environments.  The FSC® certification ensures that products come from well managed forests that provide environmental, social, and economic benefits.  The FSC® chain of custody certification verifies that FSC® certified material is identified or kept segregated from non-certified or non-controlled material through this chain. Fasson® 60# Classic® Laid Solar White WS FSC® is an ideal facestock for wine, high-end beverages and gourmet foods.



Basis Weight:
60# per ream ± 10%
(500 sheets 25" x 38")


Caliper:
0.0054 inches ± 10%


Tensile:
MD 19# per inch width
CD 13# per inch width


Tear:
N/A


Stiffness:
N/A
Adhesive:
Fasson® S100R is a permanent adhesive which is removable in minimum 100° F water. Developed with good initial tack and ultimate adhesion, S100R can be used as a permanent adhesive on many substrates, yet be removed from that substrate after immersion in water hotter than 100° F. Removal times will vary due to differences in facestocks and substrates. It might be as short as 30 seconds from HDPE, or as long as 5 minutes. Where removal is required, this adhesive is recommended for use on HDPE, polypropylene, poly vinyl chloride (PVC), polyester, Lexan®, stainless steel, and glass. We do not recommend it for use with film facestocks (i.e., polypropylene, polystyrene), due to a potential surface interaction which could cause the loss of water removability. This adhesive exhibits excellent diecutting and stripping properties.

FDA Compliance:  Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105).  Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.

Lexan® is a registered trademark of General Electric Company.



Type:
Emulsion Acrylic


Minimum Application Temperature:
+20° F


Service Temperature Range:
-65° F to 200° F
Typical Performance Data: 60# C1S Paper at room temperature on standard lab panels


Stainless Steel
Loop Tack:
Peel Adhesion:

2.6 lbs
1.8 lbs - Tear

HDPE
Loop Tack:
Peel Adhesion:

1.6 lbs
1.1 - 1.6 lbs

PET
Loop Tack:
Peel Adhesion:

2.6 lbs
1.2 lbs -Tear

Glass
Loop Tack:
Peel Adhesion:

2.7 lbs
1.9 lbs -Tear





Liner:
44#PK is a poly-coated natural kraft (brown) paper liner for roll-to-roll applications. Specially designed for high-speed automatic label dispensing applications. Not recommended for sheeting or fanfolding. NOTE: Liner color variation may occur.



Basis Weight:
43.50# per ream ±10%
(24" x 36" 500 sheets)


Caliper:
0.0031 inches ± 10%


Tensile:
MD 35 pounds per inch width
CD 13 pounds per inch width


Tear:
MD 35 grams
CD 50 grams
Total Construction Caliper (approximate): 0.0093 inches ± 10%

Fasson® and all other Avery brands, product names and codes are trademarks of Avery Dennison Corporation.


Applications and Uses
This product is suitable for use in a wide variety of prime labeling applications where facestock appearance is critical, especially wine labeling applications. This adhesive can be used as a permanent adhesive on many substrates, yet be removed from that substrate after immersion in water hotter than 100°F. Removal times will vary due to differences in facestocks and substrates. It might be as short as thirty seconds from HDPE, but might be as long as five minutes. When removal is required, this adhesive is recommended for use on HDPE, PVC, PET, LEXAN™, stainless steel, and glass. We do not recommend it for use on polypropylene or polystyrene due to a potential surface interaction, which could cause the loss of water removability.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Statement of Practical Use
All materials, sales and contracts for sale of Avery Dennison products are sold with the express requirement and understanding that the customer is solely and exclusively responsible for testing and for ensuring the products are fit for the customer's purposes or an end-user's purposes. All express or implied warranties of merchantability and fitness for particular use are disclaimed.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.


label.averydennison.com

Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511