Durable Form

DURABLE PORTFOLIO

Product Data Sheet

Fasson® 2 Mil Matte Chrome Polyester TC/S8015/50#SCK

Spec#: 76660 - Durable

Facestock	Facestock physical properties
2 Mil Matte Chrome Polyester TC is a matte finished metallic film featuring excellent tear strength, heat resistance, dimensional stability, opacity and chemical resistance. Designed for printing with most solvent and some water-based flexographic inks. Suitable for thermal transfer printing applications with select thermal transfer ribbons. Specific testing required.			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		0.0020	inches	50.80	micron
	Tensile: ASTM D882	MD	22,700	PSI	1,596	kg/sq cm
	Tensile: ASTM D882	CD	29,800	PSI	2,095	kg/sq cm

Adhesive	Adhesive physical properties
S8015 adhesive is a high strength clear adhesive featuring high initial tack, adhesion and shear. Offers strong permanent bonding to a wide variety of substrates including high surface energy (HSE), low surface energy (LSE) and powder coat substrates. Excellent chemical and UV resistance.			Imperial Value	Units	Metric Value	Units
	Type:		Solvent Acrylic
	Caliper: ASTM D1000		0.0011	inches	27.94	micron
	Standard Coat Wt:				32	g/sq m
	Minimum Appl Temp:		45	F	7	C
	Service Temp Range:	Min	-30	F	-34	C
	Service Temp Range:	Max	300	F	149	C
	Loop Tack Stainless Steel: PSTC11		96.0	oz/in	105.6	N/100mm

Liner	Liner physical properties
50#SCK is a bleached, super-calendered paper stock with very good diecutting and matrix stripping properties. Suitable for back-printing with standard inks.			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		0.0032	inches	81.2800	microns
	Basis Wt: TAPPI T410 * (24" x 36" 500 sheets)		53.9	lb/ream	86.2	g/sq m
	Tensile: ASTM D882	MD	48.0	lb/inch	211.2	N/25 mm
	Tensile: ASTM D882	CD	26.0	lb/inch	114.4	N/25 mm
	Tear: TAPPI T414	MD	1.8	ounces	51.1	grams
	Tear: TAPPI T414	CD	2.0	ounces	56.8	grams

Liner Release: TMLI 90^o removal of Liner from Facestock.		Total Construction Caliper (approximate):
Rate of Removal	Grams/2" Width
400 inches/min.	60	0.0062 inches (6.2 mils; 157.5 micron)

DURABLE PORTFOLIO

Product Data Sheet

Features and Benefits

Opaque metallized facestock with very good hiding power and physical strength
Glossy clear top coat that accepts most flexographic, letterpress, and rotary screen inks
Very good thermal transfer printability with most wax/resin and resin ribbons
Top coat and adhesive have excellent chemical resistance

Applications and Uses
This product is suitable for wide variety of durable labeling applications such as:

Product identification labels
Barcodes and rating plates
Work in progress labels (WIP)
Property identification and asset tags
Durable goods labeling
UL969 Yellow Card link:https://iq.ul.com/ul/cert.aspx?ULID=100870385
For safety-critical medical devices, labeling to IEC 60601 standards helps to ensure the safety and effectiveness of a device
Automotive exterior or underhood labels. Meets GM14573* (preceded by GM6121M) Type A & B; FCA MS-13445* ( preceded by MS-CG121); Ford WSS-M99P41* Types A31, A32 and A33
* tested with standard substrates for base material performance. Not all test completed.
UL Rating plates. This product is UL969 and UL-c recognized for indoor and outdoor use (see appendix). For specific information, see UL file # MH17205 for conditions of recognitions

Printing and Converting
The top coat is designed for printing by flexography with most solvent and some water based inks. Specially formulated inks are normally not needed, however, testing is recommend prior to final ink selection. Suitable for thermal transfer printing applications with select ribbons and printer models. This product can be die cut and stripped at high speeds on standard web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.

DURABLE PORTFOLIO

Product Data Sheet

Appendix

Performance Data:

The following technical data should be considered representative or typical only and should not be used for specification purposes.

	Initial (15 minute dwell)		72 Hours at Room Temperature		72 Hours at 120⁰F		96 Hours at 150⁰F (65⁰C) & 80% Relative Humidity
Surface	oz/in	N/100mm	oz/in	N/100mm	oz/in	N/100mm	oz/in	N/100mm
1. Stainless Steel 2. Aluminum 3. Polypropylene 4. HDPE 5. LDPE 6. ABS Plastic	82.1 83.7 52.2 43.2 42.1 73	90.3 92.1 57.4 47.5 46.3 80.3	73.7 54.8 23.9 40.4 74.5 82.4	81.1 60.3 26.3 44.4 82 90.6	77.4 60.5 65.4 41.7 21.4 78.5	85.1 66.6 71.9 45.9 23.5 86.4	83.7 81.1 59.2 46.4 2.2 23.2	92.1 89.2 65.1 51 2.4 25.5

Environmental Performance: Chemical Resistance test results

The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.

	Adhesion to Stainless Steel		Visual	Edge
Chemical	oz/in	N/100mm	Appearance	Penetration mm
1. 70% IPA 2. Tide® Detergent 3. Engine Oil (10W30) 4. Water 5. Ammonia - pH 11 6. 409® Cleaner 7. Toluene 8. Brake Fluid 9. Reference Fuel C 10. Kerosene K1 11. Heptane	73.4 58.5 62.5 66.7 27.3 28.9 17.8 68.3 35.2 46.2 12.9	80.7 64.4 68.8 73.4 30 31.8 19.6 75.1 38.7 50.8 14.2	No Change No Change No Change No Change No Change No Change No Change No Change No Change No Change No Change	0 0 0 0 0 0 8.9 0 6.4 3.3 3.6

Compliance Recognition: UL, C-U

Underwriters Laboratories, Inc.

	Minimum Temperature		Maximum Temperature
Substrates	^oF	^oC	^oF	^oC	(I=Indoor Only I/O=Indoor & Outdoor)
1. Stainless Steel 2. Polyphenylene Oxide 3. Polyester Powder Paint 4. Unsat Thermoset Polyester 5. ABS Plastic 6. Galvanized Steel 7. Epoxy Paint 8. Porcelain 9. Alkyd Enamel 10. Aluminum 11. Epoxy Powder Paint 12. Polyester Paint 13. Acrylic Powder Paint 14. Acrylic Paint 15. Phenolic 16. Polycarbonate 17. Nylon 18. Polyethylene 19. Polypropylene 20. and others	-40 -9 -40 -40 -9 -40 -40 -40 -40 -40 -9 -9 -40 -9 -40 -9 -40	-40 -23 -40 -40 -23 -40 -40 -40 -40 -40 -23 -23 -40 -23 -40 -23 -40	302 140 302 176 104 302 302 302 302 302 302 302 302 302 212 212 176 104 104	150 60 150 80 40 150 150 150 150 150 150 150 150 150 100 100 80 40 40	I/O I/O I/O I/O I/O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I

Recognized Ribbons:

Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RF", Astro Med "RY", Coding Prds "5940", Dai Nippon "R-300", Dai Nippon "R-510", Iimak "SP-410", Iimak "SP-330", Iimak "Primemark", Intermec "TMX 1500", Intermec "TMX 3200", ITW "R-91, ITW "B324", Japan Pulp & Paper "Resin 1", Japan Pulp & Paper "Sigma P", Kurz "K300", Kurz "K500", Kurz "K501", Mid City Columbia "CGL-80HE", Mid City Columbia "MCC-23HE", NCR "Promark 3", NCR "Perma Max", NCR "K3", Ricoh "B110C", Ricoh "B110CX", Ricoh "B110CR", Ricoh "120EC", Sato Corp. "Premier 1", Sony "TR4070", Sony "TR4075", Sony "TR5070", Sony "TR6070", Sony "TR6075", Sony "Signature Series Resin", Union Chemicar "US300", Zebra "5095", Zebra "5100", Zebra "5175", Zebra "5463", Zebra "5555", Zebra "Z-4100", and others.

Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials

	Minimum Temperature		Maximum Temperature
Substrates	^oF	^oC	^oF	^oC	(I=Indoor Only I/O=Indoor & Outdoor)
1. Metals 2. Electrostatic Paints 3. Plastics Group I 4. Plastics Group II 5. Plastics Group III 6. Plastics Group IV 7. Plastics Group V 8. Plastics Group VI 9. Plastics Group VII 10. Plastics Group VIII	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40	302 302 212 176 176 176 176 176 176 176	150 150 100 80 80 80 80 80 80 80	I/O I/O I/O I/O I/O I/O I I I I

Recognized Ribbons:

Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med "RY", Dai Nippon "R-300", Dai Nippon "R-510", Japan Pulp & Paper "Resin 1", Kurz "K500", Mid City Columbia "CGL-80HE", Mid City Columbia "MCC-23HE", NCR "Promark 3", Ricoh "B110C", Ricoh "B110CR", Sato Corp. "Premier 1", Sony "TR4070", Sony "TR5070", Sony "TR6070", Sony "TR6075", Sony "Signature Series Resin", Union Chemicar "US300", Zebra "5100", and others.

409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company

The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com

Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511