Fasson® Valtuff® is a 2.5 mil clear, oriented and cross-laminated HDPE. It provides excellent strength, elongation, and barrier characteristics. Additional on-press surface preparation is required to make this material print-receptive.

Note: The cross-lamination characteristic of this HDPE facestock causes a wrinkled appearance. This "wrinkled" appearance and surface irregularity is inherent in this facestock, and should not be considered a defect; it does not affect performance.

Valtuff® is a registered trademark of Valeron® Strength Films.

	Basis Weight:	n/a
	Caliper:	0.0025 inches ±10%
	Tensile:	MD 8,300 psi ± 10% CD 8,300 psi ± 10%
	Tear:	N/A
	Stiffness:	N/A

Adhesive:
Fasson® S3000 is a clear permanent adhesive designed for prime labeling, including squeezable and clear facestock applications. Designed for low ooze and high temperature resistance. FDA Compliance: Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105). Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.

	Type:	Emulsion Acrylic
	Minimum Application Temperature:	+25° F
	Service Temperature Range:	-40° F to +176° F subject to facestock limitations

Typical Performance Data: , 2 Mil Clear Polyester Facestock at room temperature on standard lab panels

	Stainless Steel Loop Tack: Peel Adhesion:	2.0 lbs 4.3 lbs
	Aluminum Loop Tack: Peel Adhesion:	N/A 3.4 lbs
	PET Enamel Paint Loop Tack: Peel Adhesion:	N/A 4.0 lbs
	Polypropylene Loop Tack: Peel Adhesion:	N/A 2.0 lbs
	Glass Loop Tack: Peel Adhesion:	N/A 3.4 lbs

Liner:
3 mil clear non-topcoated polyester is a highly transparent film featuring excellent tear strength, heat resistance, dimensional stability, and chemical resistance.

	Basis Weight:
	Caliper:	0.0030 inches ± 10%
	Tensile:	MD 30,000 psi CD 30,000 psi
	Tear:

Adhesive:
Fasson® S3000 is a clear permanent adhesive designed for prime labeling, including squeezable and clear facestock applications. Designed for low ooze and high temperature resistance. FDA Compliance: Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105). Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.

	Type:	Emulsion Acrylic
	Minimum Application Temperature:	+25° F
	Service Temperature Range:	-40° F to +176° F subject to facestock limitations

Typical Performance Data: , 2 Mil Clear Polyester Facestock at room temperature on standard lab panels

	Stainless Steel Loop Tack: Peel Adhesion:	2.0 lbs 4.3 lbs
	Aluminum Loop Tack: Peel Adhesion:	N/A 3.4 lbs
	PET Enamel Paint Loop Tack: Peel Adhesion:	N/A 4.0 lbs
	Polypropylene Loop Tack: Peel Adhesion:	N/A 2.0 lbs
	Glass Loop Tack: Peel Adhesion:	N/A 3.4 lbs

Liner:
44#PK is a poly-coated natural kraft (brown) paper liner for roll-to-roll applications. Specially designed for high-speed automatic label dispensing applications. Not recommended for sheeting or fanfolding. NOTE: Liner color variation may occur.

	Basis Weight:	43.50# per ream ±10% (24" x 36" 500 sheets)
	Caliper:	0.0031 inches ± 10%
	Tensile:	MD 35 pounds per inch width CD 13 pounds per inch width
	Tear:	MD 35 grams CD 50 grams

Total Construction Caliper (approximate): 0.0102 inches ± 10%



Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Statement of Practical Use
All materials, sales and contracts for sale of Avery Dennison products are sold with the express requirement and understanding that the customer is solely and exclusively responsible for testing and for ensuring the products are fit for the customer's purposes or an end-user's purposes. All express or implied warranties of merchantability and fitness for particular use are disclaimed.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

label.averydennison.com

Label and Packaging Materials-North America 8080 Norton Parkway Mentor, OH 44060 800-944-8511