DURABLE PORTFOLIO
Product Data Sheet
Fasson® 2 Mil Matte Silver Checkerboard Polyester TC/S8015/50#SCK
Spec#: 78199
FacestockFacestock physical properties
A 2 mil matte silver voidable polyester film incorporating a pattern release layer which yields a 3 mm checkerboard pattern for tamper evidence when removed from a substrate. The facestock is top coated to enhance flexographic, UV leterpress, and thermal transfer printing.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
microns
Tensile:
ASTM D882
MD
28,000
PSI
1,968
Kg/sq.cm
CD
34,000
PSI
2,390
Kg/sq.cm
AdhesiveAdhesive physical properties
S8015 adhesive is a high strength clear adhesive featuring high initial tack, adhesion and shear. Offers strong permanent bonding to a wide variety of substrates including high surface energy (HSE), low surface energy (LSE) and powder coat substrates. Excellent chemical and UV resistance.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Acrylic
Caliper:
ASTM D1000
0.0011
inches
27.94
micron
Standard Coat Wt:
32
g/sq m
Minimum Appl Temp:
45
F
7
C
Service Temp Range:
Min
-30
F
-34
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
96.0
oz/in
105.6
N/100mm
LinerLiner physical properties
50#SCK is a bleached, super-calendered paper stock with very good diecutting and matrix stripping properties. Suitable for back-printing with standard inks.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
microns
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
53.9
lb/ream
86.2
g/sq m
Tensile:
ASTM D882
MD
48.0
lb/inch
211.2
N/25 mm
CD
26.0
lb/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
51.1
grams
CD
2.0
ounces
56.8
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
60
0.0062 inches (6.2 mils; 157.48 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
This product is suitable for wide variety of labeling applications such as: See Technical Bulletin "Tamper-Evident Polyesters" for proper end use and surface preparation

Printing and Converting
The top coat is designed for printing by flexography with most solvent and some water based inks. Specially formulated inks are normally not needed, however, testing is recommended prior to final ink selection. Suitable for thermal transfer printing applications with select ribbons and printer models. This product can be die cut and stripped at moderate speeds on standard web-fed presses. Not intended for auto-application. Dispensing tests must be conducted prior to committing to production..

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix



Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Stainless Steel

2. Aluminum

3. Polypropylene

4. HDPE

5. LDPE

6. ABS Plastic
82.1

83.7

52.2

43.2

42.1

73
90.3

92.1

57.4

47.5

46.3

80.3
73.7

54.8

23.9

40.4

74.5

82.4
81.1

60.3

26.3

44.4

82

90.6
77.4

60.5

65.4

41.7

21.4

78.5
85.1

66.6

71.9

45.9

23.5

86.4
83.7

81.1

59.2

46.4

2.2

23.2
92.1

89.2

65.1

51

2.4

25.5

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
73.4

58.5

62.5

66.7

27.3

28.9

17.8

68.3

35.2

46.2

12.9
80.7

64.4

68.8

73.4

30

31.8

19.6

75.1

38.7

50.8

14.2
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

0

8.9

0

6.4

3.3

3.6



Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511