DURABLE PORTFOLIO
Product Data Sheet
Fasson® 2.3 Mil White BOPP TC/S8001/50#SCK
Spec#: 78403 - Durable
Obsolete - See spec C0733 to add TC2000 TC
FacestockFacestock physical properties
2.3 Mil White BOPP TC is a heat set, biaxially-oriented, coextruded polypropylene film, with good opacity and a bright white high gloss background. The surface has been topcoated to give superior printability by UV and water-based flexographic, gravure, silkscreen and letterpress processes, using a wide variety of different inks. Also thermal transfer printable. This facestock has excellent moisture resistance, and good diecutting and dispensing characteristics.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0023
inches
58.42
micron
Tensile:
ASTM D882
MD
26,825
psi
1,886
kg/sq cm
CD
22,475
psi
1,580
kg/sq cm
AdhesiveAdhesive physical properties
S8001 is a high performance, clear permanent emulsion acrylic pressure sensitive adhesive with balanced adhesion to a wide variety of substrates, including low surface energy plastics, engineering grade plastics, bare, coated, or painted metals, including powder coat and enamel paints. It features medium tack and excellent chemical and UV resistance for outdoor industrial applications.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0010
inches
25.40
microns
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
302
F
150
C
Loop Tack Stainless
Steel: PSTC11
32.0
oz/inch
35.2
N/100 mm
LinerLiner physical properties
50# SCK is a bleached, super calendered paper stock with very good die-cutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs/ream
87.2
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
51.1
grams
CD
2.1
ounces
59.6
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
45
0.0065 inches (6.5 mils; 165.1 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
Ideal for general purpose nameplates and film label applications.
Applied labels will be resistant to water, mild acids, bases, salts, and most petroleum-based oils, greases, and aliphatic
solvents under normal vertical conditions.

Printing and Converting
Can be thermal transfer printed with wax, wax/resin combination, and resin based ribbons on standard thermal transfer printing equipment. The top coated surface accepts most flexographic, letterpress, and screen inks. Testing is recommended prior to selecting any thermal transfer ribbon or press ink for production. Can be die cut and converted at high speeds on most roll fed rotary printing equipment. Labels in a variety of shapes and sizes have been successfully dispensed on standard pressure sensitive label dispensers.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes. Data was generated from 2 mil polyester facestock applied to clean laboratory panels. See Tech Bulletin "Achieving Maximum Adhesion" for specifics.
Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. ABS Plastic

3. Polypropylene

4. HDPE

5. LDPE

6. Stainless Steel
33.8

42.3

11.0

25.5

8

35.2
37.2

46.5

12.1

28.1

8.8

38.7
58

68.9

38.4

32

56

60.4
63.9

75.8

42.1

35.2

61.6

66.5
66.9

54.7

33.9

31.1

6.8

42.9
73.6

60.1

37.3

34.2

7.5

47.2
98.4

71.8

27.7

36.2

16.5

50.6
108.3

79.0

30.5

39.8

18.2

55.7

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.
Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. K1 Kerosene

11. Heptane
46.2

40.1

51.2

19

44.8

49.2

21.7

46.4

39.4

45.7

39.6
50.8

44.1

56.4

20.9

49.3

54.1

23.9

51

43.3

50.2

43.5
No change

No change

No change

No change

No change

No change

No change

No change

No change

No change

No change
0

0

0

0

0

0

0

0

0

0

0

Compliance Recognition: UL, C-U
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Acrylic Paint

    2. Acrylic Plastic

    3. Acrylic PCP*

    4. ABS Plastic

    5. Alkyd Enamel Paint

    6. Aluminum

    7. EVA

    8. Epoxy Paint

    9. Epoxy PCP*

    10. Galvanized Steel

    11. Glass

    12. Nylon (polyamide)

    13. Phenolic

    14. PBT Plastic

    15. Polycarbonate

    16. Polyester Paint

    17. Polyester PCP*

    18. PBT Plastic

    19. Polyethylene

    20. PET Plastic

    21. Polyphenylene Oxide

    22. Polypropylene

    23. Polystyrene

    24. Polyurethane Paint

    25. Poly (Urethane) PCP*

    26. PVC (Rigid)

    27. PVF (Tedlar)

    28. Porcelain

    29. Southern Yellow Pine

    30. Stainless Steel

    31. Unsat Thermoset Polyester

    32. *PCP=Powder Coat Paint
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40


-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40


212

140

212

176

212

212

140

212

212

212

212

212

212

176

212

212

212

176

176

176

176

176

176

176

212

176

212

212

212

212

212


100

60

100

80

100

100

60

100

100

100

100

100

100

80

100

100

100

80

80

80

80

80

80

80

100

80

100

100

100

100

100


I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I
Recognized Ribbons: Armor "AXR7+", DNP "R-510", Iimak "SP-330", ITW "B324", Ricoh "B110C"



Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Metals

    2. Electrostatic Paints

    3. Plastics Group II

    4. Plastics Group III

    5. Plastics Group IV

    6. Plastics Group V

    7. Plastics Group VI

    8. Plastics Group VII

    9. Plastics Group VIII
-40

-40

-40

-40

-40

-40

-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40

-40
212

212

176

176

176

176

176

176

176
100

100

80

80

80

80

80

80

80
I

I

I

I

I

I

I

I

I
Recognized Ribbons: Armor "AXR7+", DNP "R-510", Iimak "SP-330", ITW "B324", Ricoh "B110C"


409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511