DURABLE PORTFOLIO
Product Data Sheet
Fasson® 2 Mil White Polyester TCD/S8025/50#SCK
Spec#: 78981 Durable
FacestockFacestock physical properties
2 Mil White Polyester TCD is a white pigmented facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
microns
Tensile:
ASTM D882
MD
22,000
psi
1,547
kg/cm2
CD
28,000
psi
1,968
kg/cm2
AdhesiveAdhesive physical properties
S8025 is a high performance, clear permanent solvent acrylic pressure sensitive adhesive with balanced adhesion to a wide variety of substrates, including low surface energy plastics, engineering grade plastics, bare, coated, or painted metals, including powder coat and enamel paints. It features medium tack for good short term repositionability, low ooze, and excellent chemical and UV resistance for outdoor industrial applications.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Acrylic
Caliper:
ASTM D1000
0.0009
Inches
22.86
microns
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
302
F
150
C
Loop Tack Stainless
Steel: PSTC11
50.6
oz/in
55.7
N/100 mm
LinerLiner physical properties
50#SCK is a bleached, super-calendered paper stock with very good diecutting and matrix stripping properties. Suitable for back-printing with standard inks.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
microns
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
53.9
lb/ream
86.2
g/sq m
Tensile:
ASTM D882
MD
48.0
lb/in
211.2
N/25mm
CD
26.0
lb/in
114.4
N/25mm
Tear:
TAPPI T414
MD
1.8
ounces
51.1
grams
CD
2.0
ounces
56.8
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
40
N/A

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
This product is suitable for wide variety of durable labeling applications such as:
Printing and Converting
The top coat is designed for printing by most solvent, UV cured, and water-based flexographic inks; UV cured letterpress and rotary screen inks. Specially formulated inks are not normally necessary, however, testing is recommended prior to final ink system selections.
Note: With most press inks, overlamination is required to meet the abrasion requirement for c-UL (CSA) recognition. At the 150ºC recognition temperature, overlaminations darken enough to hinder the readability of most yellow colored inks. If overlamination is desired with UL or c-UL recognition, seek recognition at a lower maximum use temperature.

Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or the Fasson Thermal Transfer Ribbon Guide for specific recommendations. This product can be die cut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Stainless Steel

2. Aluminum

3. Polypropylene

4. HDPE

5. LDPE

6. ABS Plastic
62.7

42.7

52.3

32

24.8

56.2
69

47

57.5

35.2

27.3

61.8
65.8

52.8

62.9

32

42.1

65.6
72.4

58.1

69.2

35.2

46.3

72.2
75.2

67.2

59.2

36.8

35.4

56
82.7

73.9

65.1

40.5

38.9

61.6
89.6

85.1

57.9

36.3

23.7

54.7
98.6

93.6

63.7

39.9

26.1

60.2

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
43

57.9

53.6

60

42.4

56.2

29.4

51

48.8

56.5

43
47.3

63.7

59

66

46.6

61.8

32.3

56.1

53.7

62.2

47.3
No Change

No Change

No Change

No Change

Edge Swell

No Change

Edge Swell

No Change

Edge Swell

No Change

No Change
0

0

0

0

0

0

6.4

0

0

0

0



Compliance Recognition: UL, C-U
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Acrylic Paint

    2. Alkyd Enamel Paint

    3. Aluminum

    4. Chrome Plate

    5. Epoxy Paint

    6. Epoxy PCP*

    7. Galvanized Steel

    8. Polyester Paint

    9. Polyester PCP*

    10. Poly (Urethane) PCP*

    11. Porcelain

    12. Porcelain

    13. Stainless Steel

    14. Melamine

    15. Nylon (polyamide)

    16. Phenolic

    17. Polycarbonate

    18. Unsat Thermoset Polyester

    19. ABS Plastic

    20. Epoxy

    21. HDPE

    22. PBT Plastic

    23. Polyethylene

    24. PET Plastic

    25. Polyphenylene Oxide

    26. Polyphenylene Sulfide

    27. Polypropylene

    28. Polystyrene

    29. PVC (Rigid)

    30. Acrylic Plastic
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40



-40

-40

-40

-40

-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40



-40

-40

-40

-40

-40

-40

-40
302

302

302

302

302

302

302

302

302

302

302

302

302

212

212

212

212

212

176

176

176

176

176

176

176

176

176

176

176

140
150

150

150

150

150

150

150

150

150

150

150

150

150

100

100

100

100

100

80

80

80

80

80

80

80

80

80

80

80

60
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I

I/O

I/O

I/O

I/O

I/O

I/O

I/O
Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med "RY", Coding Prds "5940", DNP "R-300", DNP "R-510", DNP "TR4070", Iimak "SP-330", Iimak "SP-575", Intermec "TMX 3200", ITW "B324", Kurz "K500", Kurz "K501", NCR "Promark 3", NCR "K3", Ricoh "B110CX", Ricoh "B110CR", Sato Corp. "Premier 1", and others.



Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Electrostatic Coated Metal A

    2. Electrostatic Coated Metal B

    3. Electrostatic Coated Metal C

    4. Electrostatic Coated Metal D

    5. Metals

    6. Plastics Group I

    7. Plastics Group II

    8. Plastics Group III

    9. Plastics Group IV

    10. Plastics Group V

    11. Plastics Group VI

    12. Plastics Group VII

    13. Plastics Group VIII
0

0

0

0

0

0

0

0

0

0

0

0

0

























302

302

302

302

302

212

176

176

176

176

176

176

176
150

150

150

150

150

100

80

80

80

80

80

80

80
I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O
Recognized Ribbons:


409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511