Durable Form

DURABLE PORTFOLIO

Product Data Sheet

Fasson® 2 Mil White Polyester TC/S8049/50#SCK ABC

Spec#: 79453 Durable

Facestock	Facestock physical properties
2 Mil White Polyester is a homogeneously pigmented white facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance. The topcoat is designed to provide excellent printability with most UV and water based Flexo printing, along with compatibility to most TT ribbons			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		0.0020	inches	50.80	micron
	Tensile: ASTM D882	MD	21,300	PSI	1,497	kg/cm2
	Tensile: ASTM D882	CD	28,400	PSI	1,997	kg/cm2

Adhesive	Adhesive physical properties
S8049 is a rubber hybridized acrylic adhesive with extremely high final adhesion on a wide variety of surfaces, including textured and low surface energy substrates. This adhesive has excellent chemical resistance.			Imperial Value	Units	Metric Value	Units
	Type:		S8049 Durable
	Caliper: ASTM D1000		0.0018	inches	45.72	micron
	Standard Coat Wt:				45	g/sq m
	Minimum Appl Temp:		41	F	5	C
	Service Temp Range:	Min	-40	F	-40	C
	Service Temp Range:	Max	302	F	150	C
	Loop Tack Stainless Steel: PSTC11		6.2	lb/in	0.0

Liner	Liner physical properties
50# SCK is a bleached, super-calendered paper stock with very good diecutting and matrix stripping properties. Used for standard roll-to-roll and fanfolded applications. For best results, fanfolded products must be processed in a controlled environment of 40-50% RH. Not recommended for sheeted applications. Features good back printability.			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		3.1900	mil	0.0000
	Basis Wt: TAPPI T410 * (24" x 36" 500 sheets)		57.7	lbs	0.0	g/sq m
	Tensile: ASTM D882	MD	51.0	lb/in	0.0
	Tensile: ASTM D882	CD	22.7	lb/in	0.0
	Tear: TAPPI T414	MD	57.1	gms	0.0
	Tear: TAPPI T414	CD	76.5	gms	0.0

Liner Release: TMLI 90^o removal of Liner from Facestock.		Total Construction Caliper (approximate):
Rate of Removal	Grams/2" Width
400 inches/min.	45	.0068 inches

DURABLE PORTFOLIO

Product Data Sheet

Features and Benefits

Opaque white facestock with very good hiding power and physical strength
Glossy clear topcoat that accepts most flexographic, letterpress, and rotary screen inks
Excellent thermal transfer printability with most wax/resin and resin ribbons
Topcoat and adhesive have excellent chemical resistance
Anti-block coating on backside of liner to resist adhesive blocking.
UL969 Yellow Card link: https://iq.ul.com/ul/cert.aspx?ULID=102738471
UL969 and c-UL Recognized. See file MH17205 for specific details on recognized conditions
Automotive exterior or underhood labels. Meets GM14573* (preceded by GM6121M) Type A & B; FCA MS-13445* ( preceded by MS-CG121); Ford WSS-M99P41* Types A31, A32 and A33
Meets FMVSS302 requirements with certain substrates.
* tested with standard substrates for base material performance. Not all test completed.
UL969 recognized on Epoxy Powder Paint, Polyester Powder Paint and Polyurethane Powder Paint textured surfaces.

Applications and Uses
This product is briefly repositionable, and then adhesion increases to a very high ultimate peel strength.
S8049 products are engineered to be resistant to harsh chemicals commonly found in the automotive and electronics industries.

Printing and Converting
The top coat is designed for printing by most solvent, UV cured, and water-based flexographic inks; UV cured letterpress, Digital and rotary screen inks. Specially formulated inks are not normally necessary, however, testing is recommended prior to final ink system selections.
Note: With most press inks, overlamination is required to meet the abrasion requirement for c-UL (CSA) recognition. At the 150ºC recognition temperature, overlaminations darken enough to hinder the readability of most yellow colored inks. If overlamination is desired with UL969,c-UL or CSA recognition, seek recognition at a lower maximum use temperature.

Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or the Fasson Thermal Transfer Ribbon Guide for specific recommendations.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.

DURABLE PORTFOLIO

Product Data Sheet

Appendix

Performance Data:

The following technical data should be considered representative or typical only and should not be used for specification purposes.

	Initial (15 minute dwell)		72 Hours at Room Temperature		72 Hours at 120⁰F		96 Hours at 150⁰F (65⁰C) & 80% Relative Humidity
Surface	oz/in	N/100mm	oz/in	N/100mm	oz/in	N/100mm	oz/in	N/100mm
1. Stainless Steel 2. Aluminum 3. ABS Plastic 4. Polypropylene 5. HDPE 6. LDPE	112.32 97.44 131.04 116.8 65.6 95.2	122.69 106.5 143.13 127.84 71.60 104.06	139.04 138.88 134.28 124.8 117.12 128.8	151.85 151.81 146.7 136.37 128 140.73	140.16 136.32 102.40 128.48 47 67.36	153.11 148.9 111.88 140.37 20.23 73.65	139.04 130.88 65.76 107.52 125.28 60.32	152.01 143.01 71.87 117.46 136.84 65.94

Compliance Recognition: UL, C-U

Underwriters Laboratories, Inc.

	Minimum Temperature		Maximum Temperature
Substrates	^oF	^oC	^oF	^oC	(I=Indoor Only I/O=Indoor & Outdoor)
1. Acrylic Paint 2. Acrylic PCP* 3. Alkyd Enamel Paint 4. Aluminum 5. Epoxy Paint 6. Epoxy PCP* 7. Galvanized Steel 8. Polyester Paint 9. Polyester PCP* 10. Poly (Urethane) PCP* 11. Stainless Steel 12. Unsat Thermoset Polyester 13. Nylon (polyamide) 14. Phenolic 15. ABS Plastic 16. Polyphenylene Oxide 17. Polystyrene 18. Polycarbonate 19. Polypropylene	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40	302 302 302 302 302 302 302 302 302 302 302 302 212 212 176 176 176 176 176	150 150 150 150 150 150 150 150 150 150 150 150 100 100 80 80 80 80 80	I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

Recognized Ribbons:

Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RF", Astro Med "RY", Coding Prds "5940", DNP "R-300", DNP "R-510", DNP "TR4070", DNP "Signature Series Resin", Iimak "SP-410", Iimak "SP-330", Iimak "Primemark", Intermec "TMX 1500", Intermec "TMX 3200", ITW "B324", Kurz "K300", Kurz "K500", Kurz "K501", NCR "Promark 3", NCR "Pacesetter", NCR "Ultra V", NCR "Perma Max", NCR "K3", Ricoh "B110C", Ricoh "B110CR", Ricoh "120EC", Sato Corp. "Premier 1", Zebra "5095", Zebra "5175", Zebra "5463", Zebra "5555", and others., Fujicopian FTX303, Fujicopian FTX303N, Fujicopian TTM-164, Fujicopian FTX304, Fujicopian TTM-46

Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials

	Minimum Temperature		Maximum Temperature
Substrates	^oF	^oC	^oF	^oC	(I=Indoor Only I/O=Indoor & Outdoor)
1. Electrostatic Coated Metal C 2. Electrostatic Coated Metal D 3. Metals 4. Plastics Group I 5. Plastics Group II 6. Plastics Group III 7. Plastics Group IV 8. Plastics Group V 9. Plastics Group VI 10. Plastics Group VII 11. Plastics Group VIII	0 0 0 0 0 0 0 0 0 0 0		302 302 302 212 212 176 176 176 176 176 176	150 150 150 100 100 80 80 80 80 80 80	I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

Recognized Ribbons:

Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med "RY", DNP "R-300", DNP "R-510", DNP "TR4070", DNP "Signature Series Resin", Kurz "K500", NCR "Promark 3", Ricoh "B110C", Ricoh "B110CR", Sato Corp. "Premier 1", Zebra "5100", and others.

409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company

The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com

Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511