Print this Page
Fasson® 60# Classic Crest® Solar White WS FSC®/S100R/44#PK
Spec# 12623
Facestock:
Fasson® 60# Classic Crest® Smooth Solar White WS is a solar white uncoated sixty pound paper that features a smooth finish and a wet strength additive that increases resistance to tearing and shriveling in moist environments. The surface provides good printability by UV Inkjet, UV letterpress, flexographic UV, solvent and water-based inks. This facestock has been qualified on the Durst® Tau 330, Jetrion® 4900 and 4950 models. Additional product constructions utilizing the same facestock are available. The Fasson® 60# Classic Crest® Smooth Solar White WS provides an ideal print surface for wine, high-end beverages, and gourmet food. Use caution when applying inks out to the edge of the label, particularly UV cured inks and varnishes. High shrinkage coatings can cause labels to lift off the liner or substrate.

NOTE: In-house testing is always recommended prior to final ink selection. Qualification is subjective evaluation and customer perception may differ. As label designs vary, we encourage end application testing of all materials

Fasson® and all other Avery Dennison brands, product names and codes are trademarks of the Avery Dennison Corporation. All other brands and product names are trademarks of their respective owners. All statements, technical information and/or recommendations in this document are based on tests believed to be reliable but do not constitute a guarantee or warranty by Avery Dennison.



Basis Weight:
60# per ream ± 10%
(500 sheets 25" x 38")


Caliper:
0.0047 inches ± 10%


Tensile:
MD 27# per inch width
CD 15# per inch width


Tear:
N/A


Stiffness:
N/A

Adhesive:
Fasson® S100R is a permanent adhesive which is removable in minimum 100° F water. Developed with good initial tack and ultimate adhesion, S100R can be used as a permanent adhesive on many substrates, yet be removed from that substrate after immersion in water hotter than 100° F. Removal times will vary due to differences in facestocks and substrates. It might be as short as 30 seconds from HDPE, or as long as 5 minutes. Where removal is required, this adhesive is recommended for use on HDPE, polypropylene, poly vinyl chloride (PVC), polyester, Lexan®, stainless steel, and glass. We do not recommend it for use with film facestocks (i.e., polypropylene, polystyrene), due to a potential surface interaction which could cause the loss of water removability. This adhesive exhibits excellent diecutting and stripping properties.

FDA Compliance:  Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105).  Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.

Lexan® is a registered trademark of General Electric Company.



Type:
Emulsion Acrylic


Minimum Application Temperature:
+20° F


Service Temperature Range:
-65° F to 200° F


Typical Performance Data: 60# C1S Paper at room temperature on standard lab panels



Stainless Steel
Loop Tack:
Peel Adhesion:

2.6 lbs
1.8 lbs - Tear


HDPE
Loop Tack:
Peel Adhesion:

1.6 lbs
1.1 - 1.6 lbs


PET
Loop Tack:
Peel Adhesion:

2.6 lbs
1.2 lbs -Tear


Glass
Loop Tack:
Peel Adhesion:

2.7 lbs
1.9 lbs -Tear






Liner:
44#PK is a poly-coated natural kraft (brown) paper liner for roll-to-roll applications. Specially designed for high-speed automatic label dispensing applications. Not recommended for sheeting or fanfolding. Features good back printability.



Basis Weight:
44.5# per ream ±10%
(24" x 36" 500 sheets)


Caliper:
0.0032 inches ± 10%


Tensile:
MD 25# per inch width
CD 20# per inch width


Tear:
MD 40 grams
CD 50 grams

Total Construction Caliper (approximate): 0.0087 inches ± 10%


Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Statement of Practical Use
All materials, sales and contracts for sale of Avery Dennison products are sold with the express requirement and understanding that the customer is solely and exclusively responsible for testing and for ensuring the products are fit for the customer's purposes or an end-user's purposes. All express or implied warranties of merchantability and fitness for particular use are disclaimed.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.


label.averydennison.com

Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511