Durable Form

DURABLE PORTFOLIO

Product Data Sheet

Fasson® 2 Mil White Polyester TC/S8025/50#SCK

Spec#: 77920 - Durable

Facestock	Facestock physical properties
2 Mil White Polyester TC is a homogeneously pigmented white facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance.			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		0.0020	inches	50.80	micron
	Tensile: ASTM D882	MD	21,300	PSI	1,497	kg/cm2
	Tensile: ASTM D882	CD	28,400	PSI	1,997	kg/cm2

Adhesive	Adhesive physical properties
S8025 is a high performance, clear permanent solvent acrylic pressure sensitive adhesive with balanced adhesion to a wide variety of substrates, including low surface energy plastics, engineering grade plastics, bare, coated, or painted metals, including powder coat and enamel paints. It features medium tack for good short term repositionability, low ooze, and excellent chemical and UV resistance for outdoor industrial applications.			Imperial Value	Units	Metric Value	Units
	Type:		Solvent Acrylic
	Caliper: ASTM D1000		0.0009	Inches	22.86	microns
	Standard Coat Wt:				27	g/sq m
	Minimum Appl Temp:		50	F	10	C
	Service Temp Range:	Min	-40	F	-40	C
	Service Temp Range:	Max	302	F	150	C
	Loop Tack Stainless Steel: PSTC11		50.6	oz/in	55.7	N/100 mm

Liner	Liner physical properties
50#SCK is a bleached, super-calendered paper stock with very good diecutting and matrix stripping properties. Suitable for back-printing with standard inks.			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		0.0032	inches	81.2800	microns
	Basis Wt: TAPPI T410 * (24" x 36" 500 sheets)		53.9	lb/ream	86.2	g/sq m
	Tensile: ASTM D882	MD	48.0	lb/inch	211.2	N/25 mm
	Tensile: ASTM D882	CD	26.0	lb/inch	114.4	N/25 mm
	Tear: TAPPI T414	MD	1.8	ounces	51.1	grams
	Tear: TAPPI T414	CD	2.0	ounces	56.8	grams

Liner Release: TMLI 90^o removal of Liner from Facestock.		Total Construction Caliper (approximate):
Rate of Removal	Grams/2" Width
400 inches/min.	55	0.0062 inches (6.2 mils; 154.9 microns)

DURABLE PORTFOLIO

Product Data Sheet

Features and Benefits

Opaque white facestock with very good hiding power and physical strength
Glossy clear topcoat which accepts most flexographic, letterpress, and rotary screen inks
Excellent thermal transfer printability with most wax/resin and resin ribbons
Topcoat and adhesive have excellent chemical resistance

Applications and Uses
This product is suitable for wide variety of durable labeling applications such as:

Product identification labels
Barcodes and rating plates
Work in progress labels (WIP)
Property identification and asset tags
Durable goods labeling
Automotive exterior or underhood labels. Meets GM14573* (preceded by GM6121M) Type A & B; FCA MS-13445* ( preceded by MS-CG121); Ford WSS-M99P41* Types A31, A32 and A33
Meets FMVSS302 requirements with certain substrates.
For safety-critical medical devices, labeling to IEC 60601 standards helps to ensure the safety and effectiveness of a device
UL969 Yellow card link: https://iq.ul.com/ul/cert.aspx?ULID=100076180
UL969 ,c-UL (CSA) and CSA recognized for indoor and outdoor use. Specific recognition information will be found in UL969 file # MH17205 and CSA file # 097198_L_00.

Printing and Converting
The top coat is designed for printing by most solvent, UV cured, and water-based flexographic inks; UV cured letterpress, Digital and rotary screen inks. Specially formulated inks are not normally necessary, however, testing is recommended prior to final ink system selections.
Note: With most press inks, overlamination is required to meet the abrasion requirement for c-UL (CSA) recognition. At the 150ºC recognition temperature, overlaminations darken enough to hinder the readability of most yellow colored inks. If overlamination is desired with UL969,c-UL or CSA recognition, seek recognition at a lower maximum use temperature.

Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or the Fasson Thermal Transfer Ribbon Guide for specific recommendations. This product can be die cut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.

DURABLE PORTFOLIO

Product Data Sheet

Appendix

SHELF LIFE:
Unless specified otherwise in this document, one year when stored at 72F and 50% RH.

Performance Data:

The following technical data should be considered representative or typical only and should not be used for specification purposes.

	Initial (15 minute dwell)		72 Hours at Room Temperature		72 Hours at 120⁰F		96 Hours at 150⁰F (65⁰C) & 80% Relative Humidity
Surface	oz/in	N/100mm	oz/in	N/100mm	oz/in	N/100mm	oz/in	N/100mm
1. Stainless Steel 2. Aluminum 3. Polypropylene 4. HDPE 5. LDPE 6. ABS Plastic	62.7 42.7 52.3 32 24.8 56.2	69 47 57.5 35.2 27.3 61.8	65.8 52.8 62.9 32 42.1 65.6	72.4 58.1 69.2 35.2 46.3 72.2	75.2 67.2 59.2 36.8 35.4 56	82.7 73.9 65.1 40.5 38.9 61.6	89.6 85.1 57.9 36.3 23.7 54.7	98.6 93.6 63.7 39.9 26.1 60.2

Environmental Performance: Chemical Resistance test results

The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.

	Adhesion to Stainless Steel		Visual	Edge
Chemical	oz/in	N/100mm	Appearance	Penetration mm
1. 70% IPA 2. Tide® Detergent 3. Engine Oil (10W30) 4. Water 5. Ammonia - pH 11 6. 409® Cleaner 7. Toluene 8. Brake Fluid 9. Reference Fuel C 10. Kerosene K1 11. Heptane	43 57.9 53.6 60 42.4 56.2 29.4 51 48.8 56.5 43	47.3 63.7 59 66 46.6 61.8 32.3 56.1 53.7 62.2 47.3	No Change No Change No Change No Change Edge Swell No Change Edge Swell No Change Edge Swell No Change No Change	0 0 0 0 0 0 6.4 0 0 0 0

Compliance Recognition: UL, C-U

Underwriters Laboratories, Inc.

	Minimum Temperature		Maximum Temperature
Substrates	^oF	^oC	^oF	^oC	(I=Indoor Only I/O=Indoor & Outdoor)
1. Acrylic Paint 2. Alkyd Enamel 3. Aluminum 4. Epoxy Paint 5. Galvanized Steel 6. Polyester Paint 7. Polyester PCP* 8. Polyurethane PCP* 9. Porcelain 10. Stainless Steel 11. Epoxy PCP* 12. Melamine 13. Nylon 14. Polycarbonate 15. Thermoset Polyester 16. ABS Plastic 17. PBT Plastic 18. Polystyrene 19. Polyphenylene Oxide 20. Polypropylene 21. *PCP=Powder Coat Paint 22. Polyethylene Terephthalate	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40	302 302 302 302 302 302 302 302 302 302 302 212 212 212 212 176 176 176 176 176 302 176	150 150 150 150 150 150 150 150 150 150 150 100 100 100 100 80 80 80 80 80 150 80	I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

Recognized Ribbons:

Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RF", Astro Med "RY", Coding Prds "5940", Iimak "SP-410", Iimak "SP-330", Iimak "Primemark", Intermec "TMX 1500", Intermec "TMX 3200", ITW "B324", Kurz "K300", Kurz "K500", Kurz "K501", NCR "Promark 3", NCR "Pacesetter", NCR "Ultra V", NCR "Perma Max", NCR "K3", Ricoh "B110C", Ricoh "B110CR", Ricoh "120EC", Sato Corp. "Premier 1", Zebra "5095", Zebra "5100", Zebra "5175", Zebra "5463", Zebra "5555", Zebra "Z-4100", and others., Fujicopian FTX303, Fujicopian FTX303N, Fujicopian TTM-164, Fujicopian FTX304, Fujicopian TTM-46, Fujicopian FTX100, Fujicopian TRX-21, Dai Nippon "R-300", Dai Nippon "R-510", Sony "TR4070", Sony "TR4075", Sony "TR5070", Sony "TR6070", Sony "TR6075", Sony "TRX75", Sony "Signature Series Resin", Union Chemicar "US300"

Tested by Underwriters Laboratories, Inc.
to meet the requirements of the Canadian Standards Association for labeling materials

	Minimum Temperature		Maximum Temperature
Substrates	^oF	^oC	^oF	^oC	(I=Indoor Only I/O=Indoor & Outdoor)
1. Metals 2. Electrostatic Paints 3. Plastics Group I 4. Plastics Group II 5. Plastics Group III 6. Plastics Group IV 7. Plastics Group V 8. Plastics Group VI 9. Plastics Group VII 10. Plastics Group VIII	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40	-40 -40 -40 -40 -40 -40 -40 -40 -40 -40	302 302 212 176 176 176 176 176 176 176	150 150 100 80 80 80 80 80 80 80	I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

Recognized Ribbons:

Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med "RY", Kurz "K500", NCR "Promark 3", Ricoh "B110C", Ricoh "B110CR", Sato Corp. "Premier 1", Zebra "5100", and others., Fujicopian FTX304, Fujicopian TTM-46, Dai Nippon "R-300", Dai Nippon "R-510", Sony "TR4070", Sony "TR5070", Sony "TRX75", Sony "Signature Series Resin", Union Chemicar "US300"

409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company

The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com

Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511