DURABLE PORTFOLIO
Product Data Sheet
2.3 Mil White BOPP TC/S6600/50#SCK
Spec#: 77536 DURABLE
Obsolete-see spec C0732 to add TC2000
FacestockFacestock physical properties
2.3 Mil White BOPP TC is a heat set, biaxially-oriented, coextruded polypropylene film, with good opacity and a bright white high gloss background. The surface has been topcoated to give superior printability by UV and water-based flexographic, gravure, silkscreen and letterpress processes, using a wide variety of different inks. Also thermal transfer printable. This facestock has excellent moisture resistance, and good diecutting and dispensing characteristics.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0023
inches
58.42
micron
Tensile:
ASTM D882
MD
26,825
psi
1,886
kg/sq cm
CD
22,475
psi
1,580
kg/sq cm
AdhesiveAdhesive physical properties
S6600 is a highly aggressive tackified emulsion acrylic permanent adhesive with high adhesion to to a wide variety of substrates including low surface energy substrates such as polypropylene, HDPE and LDPE.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0011
inches
27.94
micron
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
30
F
-1
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
76.5
oz/inch
84.2
N/100 mm
LinerLiner physical properties
50# SCK is a bleached, super calendered paper stock with very good die-cutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs/ream
87.2
g/sq m
Tensile:
ASTM D882
MD
48.0
lbs/inch
211.2
N/25 mm
CD
26.0
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
51.1
grams
CD
2.1
ounces
59.6
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
50
0.0063 inches (6.3 mils; 160 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
This product is suitable as base stock for lead-acid vehicle battery labeling. However, it must be combined with an appropriately
qualified self-wound polypropylene overlaminate to pass typical end user battery acid test protocols. Also ideal for other general
purpose nameplates and film label applications requiring a very aggressive adhesive. Applied labels will be resistant to water,
mild acids, bases, salts, and most petroleum-based oils, greases, and aliphatic solvents under normal vertical conditions.

Printing and Converting
Specially formulated acid-resistant inks might be required to pass end user specifications. Consult your ink manufacturer for recommendations. Testing of printed labels is recommended prior to selecting a specific ink system. This product can be diecut and stripped at moderate speeds on standard web-fed presses. Sample labels in a variety of shapes have been dispensed and applied successfully with standard labeling systems. Can be thermal transfer printed using thermal transfer ribbons listed in the UL File MH17205, however other ribbons may also be suitable. Testing is recommended prior to committing to a specific thermal ribbon.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
FDA Compliance:
Fasson® S-6600 adhesive compositionally complies with Title 21 Code of Federal Regulations (C.F.R.) Section 175.105 ("Adhesives"). Compliance with this regulation permits the use of this adhesive in applications provided the adhesive is separated from food by a functional barrier or 1) with dry food, the quantity of the adhesive does not exceed the limits of good manufacturing practice, or 2) with fatty and aqueous foods, the quantity of the adhesive that contacts the food does not exceed the trace amount at seams and at the edge exposure between packaging laminates that may occur within the limits of good manufacturing practice.

Fasson Roll North America has not conducted any migratory, taste or odor studies to determine which packaging substrates would be considered suitable functional barriers for adhesives. It is therefore recommended that you or your customer(s) perform the appropriate tests to ensure that the components of the adhesives do not migrate to food at more than insignificant levels. Likewise, the inks and any other materials that you may be used to produce the final label product should also be considered for evaluation and analysis

Compliance Recognition: UL
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Aluminum

    2. Acrylic Paint

    3. Alkyd Enamel

    4. Nylon

    5. Porcelain

    6. ABS Plastic

    7. Polyphenylene Oxide

    8. Polystyrene

    9. Melamine

    10. Phenolic

    11. Polycarbonate

    12. Epoxy PCP*

    13. Thermoset Polyester

    14. Polypropylene

    15. Polyethylene

    16. Acrylic Plastic

    17. Outdoor Requires Overlamination

    18. Poly (Urethane) PCP*

    19. Polyester PCP*

    20. Stainless Steel
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40





-40



-40

-40

-40
-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40

-40





-40



-40

-40

-40
212

212

212

212

176

176

176

176

176

176

176

176

176

176

176

212



212

212

212
100

100

100

100

80

80

80

80

80

80

80

80

80

80

80

100



100

100

100
I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I



I/O

I/O

I/O
Recognized Ribbons: Armor "AXR7+", Astro Med Inc "R-5", DNP "R-510", DNP "TRX-55", Iimak "SP-330", Iimak "SP-575", Iimak "R2Prime", ITW "B324", Ricoh "B110C", Zebra "Z-4100", Japan Pulp & Paper "Resin 1", Sony "TR5050", Sony "TRX-50"





409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511