Print this Page
Fasson® PRIMAX® 350/S1000/50#SCK
Spec# 71568
Facestock:
Fasson® PRIMAX® 350 is a corona-treated, flexible, white opaque polyolefin film with exceptional dimensional stability for use in a wide range of applications, including prime label. Printable by web screen, UV letterpress, flexo solvent, and water-based inks. Use of in-line corona treatment will greatly expand the number of inks which can be used. Use caution when applying inks out to the edge of the label, particularly UV screen inks and UV cured varnishes. High shrinkage coatings can cause labels to lift off the liner or substrate. In-house testing is always recommended prior to final ink selection.

This product can be diecut and stripped at high speeds on standard web-fed presses using typical film tooling. Excellent dispensability with direct comparison to white Opticite* and better performance over clear MDPE and clear flex vinyl.

NOTE: Opticite* is a trademark of The Dow Chemical Company.



Basis Weight:
n/a


Caliper:
0.0035 inches ± 10%


Tensile:
MD 15,000 psi target
CD 1,780 psi


Tear:
n/a


Stiffness:
n/a
Adhesive:
Fasson® S1000 is a clear permanent adhesive specifically designed to exhibit excellent wet-out characteristics on clear films. Frequently used in the prime label market where squeezability and clear labeling are critical. Meets the requirements of FDA Compliance: Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105). Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.



Type:
Emulsion acrylic


Minimum Application Temperature:
+10° F


Service Temperature Range:
-40° F to +200° F, subject to facestock limitations
Typical Performance Data: 2 Mil Clear Polyester facestock at room temperature on standard lab panels


Stainless Steel
Loop Tack:
Peel Adhesion:

3.2 - 3.6 lbs
1.9 - 2.3 lbs

HDPE
Loop Tack:
Peel Adhesion:

1.0 - 1.5 lbs
0.8 - 1.3 lbs

Glass
Loop Tack:
Peel Adhesion:

2.8 - 3.3 lbs
2.0 - 2.3 lbs










Liner:
50#SCK is a bleached, super calendered paper stock with very good diecutting and matrix stripping properties. Used for standard roll-to-roll and fanfolded applications. For best results, fanfolded products must be processed in a controlled environment of 40-50% RH. Not recommended for sheeted applications. Features good back printability.



Basis Weight:
53.1# per ream ±10%
(24"x36" sheets)


Caliper:
0.0032 inches ± 10%


Tensile:
MD 44# per inch width
CD 22# per inch width


Tear:
MD 54 grams
CD 59 grams
Total Construction Caliper (approximate): 0.0073 inches ± 10%

Applications and Uses
Applied labels will remain removable from flame-treated polyethylene bottles for a maximum of 4 days and become permanent by 7 days.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Statement of Practical Use
All materials, sales and contracts for sale of Avery Dennison products are sold with the express requirement and understanding that the customer is solely and exclusively responsible for testing and for ensuring the products are fit for the customer's purposes or an end-user's purposes. All express or implied warranties of merchantability and fitness for particular use are disclaimed.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.


label.averydennison.com

Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511