DURABLE PORTFOLIO
Product Data Sheet
Fasson® 4 Mil Battery Label Vinyl/I406K/50#SCK
Spec#: 41196
FacestockFacestock physical properties
4 Mil White Semi-Rigid Vinyl that is less pliable and has lower tear strength than flexible vinyl, but has improved heat resistance and dimensional stability. Good outdoor weather resistance. Normally does not require topcoating for flexographic printing. Not recommended for process printing by rotary letterpress.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0034
inches
86.36
micron
Tensile:
ASTM D882
MD
4,500
PSI
316
kg/sq cm
CD
4,100
PSI
288
kg/sq cm
AdhesiveAdhesive physical properties
I406K A clear aggressive permanent adhesive with high initial tack and ultimate adhesion to a wide variety of substrates. Fair chemical and UV resistance.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Rubber
Caliper:
ASTM D1000
0.0010
inches
25.40
micron
Standard Coat Wt:
30
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
200
F
93
C
Loop Tack Stainless
Steel: PSTC11
128.0
oz/inch
140.8
N/100 mm
LinerLiner physical properties
50#SCK is a bleached, super-calendered kraft paper liner with very good diecutting and matrix stripping properties. Supplied with an anti-block coating ("ABC") on the backside of the liner to control adhesive and label transfer to the backside of the liner in finished, wound rolls. This liner should not be used in fanfolded label applications and is not recommended for back printability.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
53.9
lb/ream
87.9
g/sq m
Tensile:
ASTM D882
MD
48.0
lb/inch
211.2
N/25 mm
CD
26.0
lb/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.8
ounces
49.9
grams
CD
2.0
ounces
57.9
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
50
0.0076 inches

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses Will provide satisfactory outdoor durability for two years under normal vertical exposure conditions. Proper inks should be
chosen, and labels overlaminated to insure durability of graphics. This construction complies with CONEG heavy metal content
regulations.

Printing and Converting
Specially formulated acid-resistant inks might be required to pass enduser specifications. Consult your ink manufacturer for recommendations. Testing of printed labels is recommended prior to selecting a specific ink system. This product can be diecut and stripped at moderate speeds on standard web-fed presses. Sample labels in a variety of shapes have been dispensed and applied successfully with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix



Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Stainless Steel

2. Aluminum

3. ABS Plastic

4. Polypropylene

5. HDPE

6. LDPE
112

119

107

109

96

85
122

131

117.7

119

106

94
171

136.4

122.1

128

108

101
188.1

150

134.3

141

118

112
141.76

152

123.2

123

99

71
155.9

167.2

135.5

136

108

78
62.56

57.4

37.1

57

42

21
68.8

63.2

40.8

63

47

23

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. 409® Cleaner

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
49.4

48.7

62.8

59.3

49.1

43.6

0

53

68.3

15.7

21.4
54.3

53.6

69.1

65.2

54

48

0

58.3

75.2

17.3

23.5
No Change

No Change

No Change

No Change

No Change

No Change

Fell Off

No Change

No Change

No Change

No Chnage
0

0

0

0

0

0

Fell Off

0

3.1 mm

0

0




Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511