DURABLE PORTFOLIO
Product Data Sheet
Fasson® 2 Mil Matte White Polyimide/S8088/50#SCK
Spec#: 78030

FacestockFacestock physical properties
2 Mil Matte White TC Polyimide is a durable matte white top coated polyimide film with excellent tear strength, heat resistance, dimensional stability, and chemical resistance. The high opacity white top coating was specifically designed for thermal transfer printing and offers excellent scuff, scratch, UV, high temperature, and solvent resistance.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0027
inches
68.58
microns
Tensile:
ASTM D882
MD
34,000
PSI
2,390
kg/sq. cm
CD
34,000
PSI
2,390
kg/sq. cm
AdhesiveAdhesive physical properties
S8088 is a high performance acrylic based pressure sensitive adhesive featuring high ultimate adhesion and excellent resistance to PCB processing chemicals. Capable of withstanding high temperatures for extended periods of time.
Imperial Value
Units
Metric Value
Units
Type:
solvent acrylic
Caliper:
ASTM D1000
0.0009
inches
22.86
microns
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
500
F
260
C
Loop Tack Stainless
Steel: PSTC11
31.5
oz/inch
34.7
N/100 mm
LinerLiner physical properties
50# Super Calendered kraft bleached paper stock with very good die cutting and matrix stripping properties. Used for standard roll-to-roll applications. Supplied without Anit-Block Coating. Not recommended for sheeting applications.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
microns
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
57.7
lbs
92.3
g/sq m
Tensile:
ASTM D882
MD
51.0
lb/inch
224.4
N/25mm
CD
22.7
lb/inch
99.9
N/25mm
Tear:
TAPPI T414
MD
2.0
ounces
56.6
grams
CD
2.7
ounces
76.4
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
55
0.0068 inches (6.8 mils; 172.7 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Service Temperatures
Short term (90 seconds): 572ºF (300ºC) moderate discoloration, but still functional
Medium term (2 hours): 338ºF (170ºC) no visible effect
Long term (1000 hours): 212ºF (100ºC) no visible effect

Applications and Uses
This product is ideal for labeling printed circuit boards, as well as for automotive, aerospace, medical, and manufacturing applications where high temperature and solvent resistance are critical. It is able to withstand surface mount circuit board processes on either the top or bottom side of the board. This product can also be used on the top side of the board in mixed processes and is suitable for use on the bottom side when directly exposed to wave solder environment. This product meets MIL-STD-202G, Method 215J.

Printing and Converting
The topcoat is designed for thermal transfer and flexo printing when used with appropriate ribbons, and will withstand temperature spikes of up to 500ºF (260ºC). Suggested thermal transfer ribbons: DNP "R-510" and "R-300." Other ribbons might be suitable. Testing is highly recommended to insure suitable results. It might be necessary to expose printed labels to high heat in order to "set" the print, prior to any print testing. Due to the thinness of the facestock, auto-dispensing and application should be thoroughly tested prior to committing to production.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Stainless Steel

2. Aluminum

3. ABS Plastic
31.5

39.7

42.9
34.7

43.7

47.2
42.2

48.8

49.9
46.4

53.7

54.9
53.3

61.1

36.6
58.6

67.2

40.3
49.9

58.9

21.6
54.9

64.8

23.8

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
74.2

30.1

79.7

60.3

58.6

61.6

44.3

79.5

55

77.4

71.6
81.6

33.1

87.7

66.3

64.5

67.8

48.7

87.5

60.5

85.1

78.8
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

0

0

0

0

0

0





Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Stainless Steel

2. Aluminum

3. Polypropylene

4. HDPE

5. LDPE

6. ABS Plastic
31.5

39.7

0.32

0

0

42.9
34.7

43.7

0.4

0

0

47.2
42.2

48.8

0

0.8

0

49.9
46.4

53.7

0

0.9

0

54.9
53.3

61.1

0

0

1.76

36.6
58.6

67.2

0

0

1.9

40.3
49.9

58.9

0

4.32

0

21.6
54.9

64.8

0

4.8

0

23.8

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Toluene

8. Brake Fluid

9. Reference Fuel C

10. Kerosene K1

11. Heptane
74.2

30.1

79.7

60.3

58.6

61.6

44.3

79.5

55

77.4

71.6
81.6

33.1

87.7

66.3

64.5

67.8

48.7

87.5

60.5

85.1

78.8
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

0

0

0

0

0

0



Compliance Recognition: UL
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Aluminum

    2. Stainless Steel

    3. Galvanized Steel

    4. Epoxy Resin PWB
-40

-40

-40

-40
-40

-40

-40

-40
302

212

302

212
150

100

150

100
I

I

I

I
Recognized Ribbons: Dai Nippon "R-300", Dai Nippon "R-510", ITW "B324"





409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511