DURABLE PORTFOLIO
Product Data Sheet
Fasson® Laser CodeTM Drum Label TCL/S4650/79#MF ABC
Spec#: C1688 DURABLE
Rev 9.18.24

FacestockFacestock physical properties
Fasson® 4 Mil White Flexible Topcoated Vinyl has good tear strength and weather resistance, but relatively low heat resistance. The TCL topcoating (TopCoat-Laser) enhances solvent and some water-based flexographic printing. This facestock is not recommended for UV printing. Please note that due to its highly filled topcoating, this facestock is not recommended for applications requiring the use of an overlaminate. Use of an overlaminate will cause a separation of the overlaminate from the facestock if the overlaminate is tampered with. 
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0034
inches
86.36
microns
Tensile:
ASTM D882
MD
3,500
psi
246
kg/sq.cm
CD
3,000
psi
211
kg/sq.cm
AdhesiveAdhesive physical properties
Fasson® S4650 is a clear general-purpose permanent adhesive featuring good initial tack and ultimate adhesion to a wide variety of substrates. Designed for chemical drums, it provides excellent adhesion on painted steel and plastic drums. Meets the requirements of FDA 21 CFR 175.105 for indirect food contact.
Imperial Value
Units
Metric Value
Units
Type:
Emulsion Acrylic
Caliper:
ASTM D1000
0.0008
inches
20.32
Microns
Standard Coat Wt:
23
g/sq m
Minimum Appl Temp:
0
F
-18
C
Service Temp Range:
Min
-30
F
-34
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
44.0
oz/inch
48.4
N/100mm
LinerLiner physical properties
79# MF is a machine finished bleached kraft paper liner. Used primarily for roll-to-sheet applications. Suitable for laser printer constructions. The 79# machine finish is supplied with an Anti Block Coating ("ABC") on the backside of the liner to control adhesive and label transfer to the backside of the liner in finished, wound rolls. Test suitability for use in fanfold label applications due to ABC ("anti-block coating") applied to backside of the liner to control adhesive and label transfer in finished, wound rolls.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0046
inches
116.8400
microns
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
76.0
lbs/ream
121.6
g/sq m
Tensile:
ASTM D882
MD
55.0
lb/inch
242.0
N/25mm
CD
24.0
lb/inch
105.6
N/25mm
Tear:
TAPPI T414
MD
3.5
oz
99.4
grams
CD
4.2
oz
119.3
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
0.00880 inches

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
- Durable 4 Mil White flexible Vinyl
- Good tear strength
- Compliant with GHS standards
- Enhanced solvent flexographic printing
- Laser Printable


Applications and Uses
This product has passed British Standard 5609 (BS 5609:1986) Section 2 and Section 3 testing, which is necessary for International Maritime Dangerous Goods (IMDG) certification

Printing and Converting
The topcoat on this product is suitable for toner printers, but testing is recommended to ensure satisfactory toner anchorage. To maximize on-press efficiencies when converting Fasson® laser film product constructions, material should be run with Grain Direction (machine direction) perpendicular to the Feed Direction of laser printing.
For a comprehensive list of recommendations for laser products, please read this set of on-line converting tips before purchasing this product: http://label.averydennison.com/content/dam/averydennison/lpm/na/en/product%20families/Rapid-Roll/fasson%20rapid-roll%20laser%20tag/Laser%20Inkjet%20Landing%20Page/LaserInkJet-printingtips.pdf

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Aluminum

2. Stainless Steel

3. Polypropylene

4. HDPE

5. LDPE

6. Acrylic Paint

7. ABS Plastic
49.92

86.24

84.96

49.92

55.36

N/A

59.84
54.6

94.4

93.0

54.6

60.6

N/A

65.5
89.76

93.6

91.68

70.24

54.24

N/A

93.12
98.2

102.4

100.3

76.9

59.4

N/A

101.9
73.92

62.08

66.24

71.2

61.44

92.96

92.96
80.9

67.9

72.5

77.9

67.2

102.3

101.7
85.12

82.08

68.0

80.16

73.28

69.28

69.28
93.2

89.8

74.4

87.7

80.2

76.2

75.8

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Brake Fluid

8. Reference Fuel C

9. K1 Kerosene

10. Heptane
63.2

68.3

58.7

64.8

98.2

84.0

44.0

94.6

83.2

66.1
69.2

74.8

64.3

70.9

107.5

91.9

48.2

103.5

91.1

72.3
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

0

0

0

0

0



Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511