Durable Form

DURABLE PORTFOLIO

Product Data Sheet

Fasson® Smudgeproof Kimdura®/S4600/50#SCK

Spec#: 79572 - Durable

Facestock	Facestock physical properties
3.7 Mil Smudgeproof Kimdura® is a white synthetic paper designed to be compatible with both thermal transfer and flexograpic printing methods. It has good chemical resistance, tear strength, and cold temperature performance to -65° F. It is certified for Section 2 of BS 5609, and also certified for BS 5609, Section 3 with most suppliers' recommended ribbons for drum labeling.			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		0.0039	inches	99.06	micron
	Tensile: ASTM D882	MD	12	psi	1	kg/sq cm
	Tensile: ASTM D882	CD	13	psi	1	kg/sq cm

Adhesive	Adhesive physical properties
S4600 is a clear general purpose emulsion permanent adhesive featuring good initial tack and ultimate adhesion to a wide variety of substrates.			Imperial Value	Units	Metric Value	Units
	Type:		Emulsion Acrylic
	Caliper: ASTM D1000		0.0008	inches	20.32	microns
	Standard Coat Wt:				23	g/sq m
	Minimum Appl Temp:		10	F	-12	C
	Service Temp Range:	Min	-40	F	-40	C
	Service Temp Range:	Max	300	F	149	C
	Loop Tack Stainless Steel: PSTC11		44.0	oz/inch	48.4	N/100 mm

Liner	Liner physical properties
50# SCK is a bleached, super calendered paper stock with very good die-cutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting.			Imperial Value	Units	Metric Value	Units
	Caliper: ASTM D1000		0.0032	inches	81.2800	micron
	Basis Wt: TAPPI T410 * (24" x 36" 500 sheets)		54.5	lbs/ream	87.2	g/sq m
	Tensile: ASTM D882	MD	48.0	lbs/inch	211.2	N/25 mm
	Tensile: ASTM D882	CD	26.0	lbs/inch	114.4	N/25 mm
	Tear: TAPPI T414	MD	1.8	ounces	51.1	grams
	Tear: TAPPI T414	CD	2.1	ounces	59.6	grams

Liner Release: TMLI 90^o removal of Liner from Facestock.		Total Construction Caliper (approximate):
Rate of Removal	Grams/2" Width
400 inches/min.	40	.0079 inches

DURABLE PORTFOLIO

Product Data Sheet

Features and Benefits

Opaque white facestock with excellent hiding power.
A versatile general purpose acrylic adhesive suitable for most substrates.
Smudge resistant top coat suitable for impact and thermal transfer printing
Compatible with both thermal transfer and flexographic printing methods.
Good initial tack and ultimate adhesion to most substrates
IMDG (BS5609 Maritime) Certified Section 2 and 3
Compliant with GHS standards

Applications and Uses

Nameplates and part labels
Cabinet labels and wiring diagrams
WIP and tracking labels
Signage or graphic displays
POP displays
Drum Labels

Printing and Converting
This material is flexographic and letterpress printable, as well as suitable for thermal transfer printing applications with select ribbons. It is not recommended for web offset printing with conventional dryers where surface temperature of the facestock could exceed 180° F in the drying unit. Use caution when applying inks out to the edge of the label, particularly UV screen inks and UV cured varnishes. High shrinkage coatings can cause labels to lift off the liner or substrate. In-house testing is always recommended prior to ink/ribbon selection. This product can be diecut and stripped at high speeds on standard web-fed presses. Actual speeds will depend on ink coverage and die configuration. Because the fillers are highly abrasive, die life will be shortened. It is recommended that a die manufacturer be contacted for further suggestions. Sample labels in a variety of shapes have been dispensed and applied successfully with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.

DURABLE PORTFOLIO

Product Data Sheet

Appendix

Compliance Recognition:

409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company

The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com

Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511