DURABLE PORTFOLIO
Product Data Sheet
Fasson® 2 Mil White Print-Treated Polyester/S8049/50#SCK ABC
Spec#: 79733 - Durable
FacestockFacestock physical properties
2 Mil White Print-Treated polyester is a pigmented white semi-glossy film facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance. The print treatment is designed to enhance printability with a variety of printing processes.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
21,000
psi
1,476
kg/sq cm
CD
31,000
psi
2,179
kg/sq cm
AdhesiveAdhesive physical properties
S8049 is a rubber hybridized acrylic adhesive with extremely high final adhesion on a wide variety of surfaces, including textured and low surface energy substrates. This adhesive has excellent chemical resistance.
Imperial Value
Units
Metric Value
Units
Type:
S8049 Durable
Caliper:
ASTM D1000
0.0018
inches
45.72
micron
Standard Coat Wt:
45
g/sq m
Minimum Appl Temp:
41
F
5
C
Service Temp Range:
Min
-40
F
-40
C
Max
302
F
150
C
Loop Tack Stainless
Steel: PSTC11
6.2
lb/in
0.0
LinerLiner physical properties
50#SCK is a bleached super-calendered kraft stock featuring high internal strength, toughness, and tear resistance. Used primarily for roll-to-roll label applications. The 50#SCK is supplied with an Anti Block Coating ("ABC") on the backside of the liner to control adhesive and label transfer to the backside of the liner in finished, wound rolls. Test suitability for use in fanfold label applications due to ABC ("anti-block coating") applied to backside of the liner to control adhesive and label transfer in finished, wound rolls.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
57.7
lbs/ream
92.3
g/sq m
Tensile:
ASTM D882
MD
51.4
lbs/inch
231.3
N/25mm
CD
22.8
lbs/inch
102.6
N/25mm
Tear:
TAPPI T414
MD
2.0
ounce
57.0
grams
CD
2.5
ounce
71.2
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
45
.007 inches

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
This product is briefly repositionable, and then adhesion increases to a very high ultimate peel strength. 
S8049 products are engineered to be resistant to harsh chemicals commonly found in the automotive and electronics industries.

Printing and Converting
The print treated surface is designed for printing by most solvent, UV cured, and water-based flexographic inks, UV cured letterpress, and rotary screen inks. Specially formulated inks are normally not necessary, however, testing is recommended prior to final ink selection. This product can be die cut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511