DURABLE PORTFOLIO
Product Data Sheet
2 Mil WH PET TC/R8022/1.4M PET
Spec#: XRN981
FacestockFacestock physical properties
2 Mil White Polyester TC is a homogeneously pigmented white facestock featuring excellent tear strength, heat resistance, dimensional stability, opacity, and chemical resistance.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0020
inches
50.80
micron
Tensile:
ASTM D882
MD
21,300
PSI
1,497
kg/cm2
CD
28,400
PSI
1,997
kg/cm2
AdhesiveAdhesive physical properties
R-8022 is a clear repositionable semi-permanet acrylic pressure senstitive adhesive capable of adhesion to a wide variety of substrates from low to high surface energy. It features medium tack, low ooze, excellent chemical and UV resistance for outdoor use, and short term clean removability from many substrates.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Acrylic
Caliper:
ASTM D1000
0.0007
inches
17.78
microns
Standard Coat Wt:
23
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
43.0
oz/inch
193.5
N/25mm
LinerLiner physical properties
An experinmental 1.4 mil clear silicone free polyester liner for electronic or other clean room applications.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0014
inches
35.5600
microns
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
0.0
g/sq m
Tensile:
ASTM D882
MD
5,400.0
lb/in2
1,620.0
kg/cm2
CD
5,400.0
lb/in2
1,620.0
kg/cm2
Tear:
TAPPI T414
MD
0.0
0.0
CD
0.0
0.0
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
300 inches/min.
56
0.0041 inches (4.1 mil; 104 microns)

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
Applications and Uses
This product is primarily designed for electronic labeling applications such as:
Printing and Converting
The top coated facestock is designed for printing by most solvent, UV cured, and water-based flexogrpahic inks, but will also accept UV letterpress and rpotary screen inks. Specially formulated inks are normally not necessary, however, testing is recommended prior to final ink selections. Also suitable for thermal tranfer printing with select ribbons and printers. Consult the Fasson Thermal Transfer Ribbon Guide for specific ribbon recommendations. This product can be die cut and stripped at high speeds on most web-fed converting equipment. sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification purposes.


Initial
(15 minute dwell)
72 Hours at Room
Temperature
72 Hours at 1200F
96 Hours at 1500F (650C) &
80% Relative Humidity
Surface
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
oz/in
N/100mm
1. Stainless Steel

2. Aluminum

3. ABS Plastic

4. LDPE

5. Polypropylene
37

41.8

40.5

18.4

18.6
40.7

45.9

44.5

20.2

20.4
38.4

46.9

46.9

0.8

24.2
42.2

51.6

51.6

0.9

26.6
50.4

49.4

61.4

0.32

32.3
55.4

54.4

67.6

0.4

35.6
47.7

59

58.6

14.9

31.2
52.4

64.9

64.4

16.4

34.3

Environmental Performance: Chemical Resistance test results
The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 180° peel.


Adhesion to Stainless Steel
Visual
Edge
Chemical
oz/in
N/100mm
Appearance
Penetration mm
1. 70% IPA

2. Tide® Detergent

3. Engine Oil (10W30)

4. Water

5. Ammonia - pH 11

6. 409® Cleaner

7. Reference Fuel C

8. Toluene

9. Brake Fluid

10. K1 Kerosene
42.08

46.56

44.32

43.84

40.8

41.3

13.6

4.16

40.2

42.6
46.3

51.2

48.8

48.2

44.9

45.4

15.0

4.58

44.2

46.8
No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change

No Change
0

0

0

0

0

0

0.1

0.15

0

0



This product is not currently UL, c-UL, or CSA Recognized.
Compliance Recognition:






409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511