DURABLE PORTFOLIO
Product Data Sheet
Fasson® 3.5 Mil Clear Vinyl NTC/S730/50#SCK
Spec#: 79875 Durable
FacestockFacestock physical properties
Fasson® 3.5 mil Matte Clear Vinyl is a non-topcoated frosty-clear vinyl with relatively low heat resistance.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0035
inches
88.90
micron
Tensile:
ASTM D882
MD
3,100
psi
218
kg/sq. cm
CD
2,700
psi
190
kg/sq. cm
AdhesiveAdhesive physical properties
S730 is a clear solvent acrylic permanent adhesive for general purpose industrial applications. Features good intial tack and ultimate adhesion to a wide variety of substrates including medium to low surface energy plastics, and high shear for minimal cold flow or ooze characteristics.
Imperial Value
Units
Metric Value
Units
Type:
Solvent Acrylic
Caliper:
ASTM D1000
0.0009
inches
22.86
micron
Standard Coat Wt:
27
g/sq m
Minimum Appl Temp:
50
F
10
C
Service Temp Range:
Min
-40
F
-40
C
Max
300
F
149
C
Loop Tack Stainless
Steel: PSTC11
59.2
oz/inch
65.1
N/100 mm
LinerLiner physical properties
50# SCK bleached, super calendered paper stock with very good die cutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting.
Imperial Value
Units
Metric Value
Units
Caliper:
ASTM D1000
0.0032
inches
81.2800
micron
Basis Wt: TAPPI T410
* (24" x 36" 500 sheets)
54.5
lbs
88.8
g/sq m
Tensile:
ASTM D882
MD
48
lbs/inch
211.2
N/25 mm
CD
26
lbs/inch
114.4
N/25 mm
Tear:
TAPPI T414
MD
1.76
ounces
49.9
grams
CD
2.05
ounces
58.2
grams
Liner Release:
TMLI 90o removal of Liner from Facestock.		Total Construction Caliper
(approximate):
Rate of Removal
Grams/2" Width
400 inches/min.
55
.0076

DURABLE PORTFOLIO
Product Data Sheet


Features and Benefits
UL recognized under MH17205

Applications and Uses
This product will provide satisfactory outdoor durability and water resistance under normal vertical exposure conditions.
Can be used for general nameplates, point-of-purchase, graphic displays and wire-wrap applications.

Printing and Converting
Testing is recommended prior to ink selection. Nominal facestock shrinkage due to plasticizer evaporation is 5%. This product can be diecut and stripped at high speeds on standard web-fed presses. Labels of various sizes and shapes have been successfully dispensed at moderate speeds on pressure-sensitive roll label applicators.

RoHS 3 (EU 2015/863)
The Fasson® product listed above meets the requirements specified by the European Union Directive Restriction of Hazardous Substances Directive 2002/95/EC, 2011/65/EU (RoHS 2) and as amended by (EU) 2015/863 (RoHS 3) .The heavy metals and phthalates called out in this directive are not intentionally used in the manufacture of Fasson® products and the totallevel of any incidental contamination of said substances in these products would be less than 100 ppm.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application.


DURABLE PORTFOLIO
Product Data Sheet
Appendix
Compliance Recognition: UL
Underwriters Laboratories, Inc.
Minimum Temperature
Maximum Temperature
    Substrates
oF
oC
oF
oC
(I=Indoor Only I/O=Indoor & Outdoor)
    1. Stainless Steel
-40
-40
104
40
I/O
Recognized Ribbons: Iimak "SP-330", Ricoh "B110A"





409® is a registered trademark of the Clorox Company
Tide® is a registered trademark of the Procter & Gamble Company


The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at label.averydennison.com/products. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com
Label and Packaging Materials-North America
8080 Norton Parkway
Mentor, OH 44060
800-944-8511